667214

Viking ME 443 Manual

41
Zoom out
Zoom in
Previous page
1/250
Next page
39
DEFRNLITESPTNOSVDAELRU EN
0478 121 9920 D - EN
Level 6 = 75 mm
Setting the cutting height:
● Hold the handle (1), pull the lever (2)
upwards and hold.
● Set the required cutting height by
moving the machine upwards and
downwards. The current cutting height
can be read off at the cutting height
indicator (3) by means of the
marking (4).
● Release the detent lever (2) and allow it
to engage.
8.5 Level indicator
The upper part of the grass catcher
box features a level indicator (1).
The flow of air that is created by the rotary
movement of the mowing blade and is
responsible for filling the grass catcher box
raises the level indicator (2):
The grass catcher box is filled with
clippings.
When the grass catcher box is full, this
flow of air is reduced and the level
indicator drops (3):
● Empty filled grass catcher box (Ö 11.5).
9.1 General
To ensure a perfect, thick lawn, mow
regularly and keep the grass short.
Do not cut the lawn too short in hot, dry
conditions as it will dry out or burn in the
sun and become unsightly.
The cutting pattern will be better with a
sharp blade than with a blunt one; the
blade should therefore be sharpened
regularly (VIKING specialist dealer).
9.2 Correct motor load
Do not switch on the lawn mower in tall
grass or at the lowest cutting height.
The lawn mower load must never cause
the motor speed to drop significantly.
If the speed drops, select a higher cutting
height setting and/or reduce the rate of
feed.
9.3 If the mowing blade blocks
Switch off the motor immediately and
disconnect the mains plug. Then eliminate
the cause of the fault.
9.4 Thermal motor overload protection
If an overload of the motor occurs during
operation, the built-in thermal overload
protection device automatically switches
off the motor.
Causes for an overload:
– mowing excessively high grass or
cutting height adjusted too low,
– excessive rate of feed,
– inadequate cleaning of the cooling air
guide (inlet slots),
– mowing blade is blunt or worn,
– unsuitable or excessively long electric
cable – voltage loss (Ö 11.1).
Recommencing operation
Resume normal operation of the machine
following a cooling period of up to 10 min
(depending on the ambient temperature)
(Ö 11.).
The machine is equipped with several
safety devices for safe operation and for
the prevention of improper use.
10
9. Notes on working with the
machine
Risk of injury!
Untangle any knots in the cable
immediately.
Guide the electric cable behind you
when mowing. Electric cables can
be inadvertently cut when mowing
and present a tripping hazard. They
therefore involve a high accident
risk. For this reason, mow so that
the electric cable is always visible
in the area of grass that has already
been cut.
10. Safety devices
Risk of injury!
If a safety device is found to be
defective, the machine must not be
operated. Consult a specialist
dealer; VIKING recommends
VIKING specialist dealers.
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking ME 443 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking ME 443 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 14,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info