667214

Viking ME 443 Manual

39
Zoom out
Zoom in
Previous page
1/250
Next page
37
DEFRNLITESPTNOSVDAELRU EN
0478 121 9920 D - EN
ME 443, ME 443 C:
ME 443:
ME 443 C:
7.1 General
● Place the machine on level and firm
ground when performing all the
operations described.
7.2 Installing mono handlebar
(ME 443 C)
● 1 Insert sleeve (J) in the bore
on handlebar (1).
● 2 Fit two washers (L) with the convex
side facing inwards onto the sleeve.
● 3 Hold sleeve (J) and washers (L) and
insert together with handlebar (1) into
handlebar console (2).
● 4 Insert nut (M) into the handlebar
console as shown.
● 5 Insert bolt (K) from the outside
inwards through the bores in
handlebar (1) and in handlebar
console (2) and tighten.
Tightening torque:
18 - 22 Nm
Installing electric cable:
● Press electric cable (3) into the holders
on the handlebar console and
handlebar (4, 5) as shown and fasten to
the handlebar using cable clip (6).
7.3 Installing dual handlebar
(ME 443)
● Insert screw (F) through the bore
in cable guide (G).
● Fit upper handlebar (2) onto lower
handlebar sections (1).
● Attach cable guide (G) to electric
cable (3) and insert screw (F) through
the bore from the inside outwards.
● On the opposite side, insert screw (F)
from the outside inwards through the
bores.
● Fit handlebar protection (I) and screw
quick clamping devices (E) onto
screws (F) (the screw should project by
about one screw thread turn) and fold
upwards.
● Check correct assembly:
Quick-clamping devices (E) must be
sufficiently tightened so that they are
pressed tightly against the handlebar
and the upper handlebar is firmly
connected to the lower handlebar.
If the handlebar is not firmly installed or
the quick-clamping devices are not
correctly located, open the quick-
clamping devices and turn them until
they are securely fastened.
● Insert electric cable (3) into holder (4) of
the handlebar console as shown.
Installing cable clip:
● Press cable clip (H) onto the upper
handlebar. Distance between the cable
clip and switch:
25 - 27 cm
Insert electric cable (3) into cable
clip (H) as shown, close tab (5) and
allow it to engage.
6. Standard equipment
Item Designation Qty.
A Basic unit 1
B Upper part of grass catcher
box
1
C Lower part of grass catcher
box
1
D Pin 2
• Instruction manual 1
E Quick-clamping device 2
F Screw 2
G Cable guide 1
H Cable clip 1
I Handlebar protection 2
J Sleeve 1
K Screw 1
L Washer 2
M Nut 1
The standard equipment may vary
depending on the country and
version type.
7. Preparing the machine for
operation
Risk of injury!
Observe the safety instructions in
the section "For your safety" (Ö 4.).
2
3
4
Danger of electric shock!
In order to prevent damage to the
insulating layer on the handlebar,
only press on the cable clips by
hand. Do not use any tools (e.g.
hammer or screwdriver).
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking ME 443 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking ME 443 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 14,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info