785222
9
Zoom out
Zoom in
Previous page
1/40
Next page
The BMS will always generate an alarm at least 30 seconds before the contactor is opened.
A shutdown of the DC system can cause a safety risk. This is especially the case in a boat. Always make sure
to act on a pre-alarm warning, for example turn on a generator, so that the batteries are recharged.
3.7. Battery Monitor (shunt)
The Lynx Smart BMS battery monitor operates in a similar fashion as the other Victron Energy battery monitors. It contains a
shunt and battery monitor electronics.
Readout of the battery monitor data is via Bluetooth using the VictronConenct app or via a GX device or the VRM portal.
3.8. Alarm relay
The Lynx Smart BMS is equipped with an alarm relay that will activate in case there is an alarm. The relay is not configurable,
with the exception of choosing continuous or intermittent (0.8s on and 0.8s off) operation.
The alarm relay will activate under these circumstances:
Pre-alarm
Any alarm or error
The alarm relay is an SPDT relay, this means that it has 3 contacts, Common (COM), Normally open (NO) and normally closed
(NC). See below image.
COM
NC
NO
No Alarm
COM
NC
NO
Alarm
Alarm relay functionality
3.9. AUX connection
The Lynx Smart BMS is equipped with an auxiliary power supply. This supply outputs the same voltage as the system battery
voltage and is rated at a maximum continuous current rating of 1.5A.
The AUX output is active when the Lynx Smart BMS is powered up, is switched on via the remote on/off switch and when the
batteries are okay.
The AUX output is inactive when the Lynx Smart BMS is un-powered, when the battery is almost empty (cell voltage below 2.6V)
or when switched off via the remote on/off terminal.
It is recommended that the system contains a GX device, that it is powered from the AUX terminal. This so the GX device
remains powered when the contactor is open.
Never power the GX device from the battery side or it will keep consuming power when the battery is low,
when the battery voltage is low, which can cause damage to the batteries when they are further discharged.
Lynx Smart BMS
Page 6 Features
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Victron Lynx Smart BMS 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Victron Lynx Smart BMS 500 in the language / languages: English as an attachment in your email.

The manual is 3.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info