815509
17
Zoom out
Zoom in
Previous page
1/64
Next page
1717 3-90-30007474Vermont Castings • Intrepid DV-IFT Owner’s Manual_R28 • 11/23
Horizontal Termination Cap:
WARNING
!
Risk of Fire! The telescoping flue section of the
termination cap MUST be used when connecting vent.
1-1/2” (38 mm) minimum overlap of vent and
telescoping ue section is required.
Failure to maintain overlap may cause overheating and
re.
Note:Forhorizontalventrunsthroughacombustible
wall and framing dimensions, refer to appliance
installation manual.
Install the Horizontal Termination Cap
Attach slip section of cap to last vent section. Maintain 1-1/2”
overlap between slip and vent sections.
Note: For installations using black pipe, slide the
decorativewall thimble over the last vent pipebefore
connecting the termination to the pipe. When this
connectionhasbeenmade,slidethewallthimbleupto
the interior wall surface and attach with screws provided.
Secure termination cap to exterior wall using provided holes
and fasteners.
Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
Flash and seal as appropriate for siding material at outside
edges of cap.
When installing a horizontal termination cap, follow the cap
location guidelines as prescribed by current ANSI Z223.1
and CAN/CGA-B149 installation codes.
CAUTION
!
Risk of Burns! Local codes may require installation of a
termination guard to prevent anything or anyone from
touching the hot cap.
DivertRoofRun-o󰀨
HHT recommends, where excessive water run-o󰀨 is possible,
use of one of the two options shown in Figure 3.9 to prevent
water running off the roof and onto/into the horizontal
termination cap.
Vertical Side Wall Installation:
NOTE: Refer to Figures 2.8 thru 2.10 for restrictor plate
adjustments for vertical vent runs.
1. Locate vent opening on the wall. It may be necessary
to rst position the stove and measure to obtain hole
location. Depending on whether the wall is combustible
or noncombustible, cut opening to size, Figure
3.10 (For combustible walls rst frame in opening.)
Combustible Walls: Cut a 10" H x 10" W (254 x 254 mm) hole
through the exterior wall and frame as shown, Figure 30.
Noncombustible Walls: Hole opening must be 7-1/2"
(191 mm) in diameter.
NOTE:Whenusingexvent,theopeningwillhaveto
bemeasuredaccordingtothe1/2”(13mm)risein12”
(305mm)ventrun.
Install gutter
Install L-shaped
diverter
Figure 3.9 - Locate Vent Opening on Wall
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Intrepid - Gas at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Intrepid - Gas in the language / languages: English as an attachment in your email.

The manual is 17.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info