756782
11
Zoom out
Zoom in
Previous page
1/16
Next page
POWX07583 EN
Copyright © 2021 VARO P a g e | 11 www.varo.com
11.10 Install vertical clamping device (Fig. 11)
Find out the vertical clamping device set (25).
Insert the iron bar of the vertical clamping device set into the back hole of the reference
ruler (13).
Adjustable Wing Screws to select height as required. Control the adjustable height of the
wing screw.
There are two round holes on the left and right sides behind the reference ruler (13), which
can be used to locate the vertical clamping device according to the work needs.
NOTE: Place the vertical clamping device on the right side of mitre saw
table when the machine is used to make bevel cuts.
11.11 Mounting the side extensions (Fig. 12)
Loosen right / left sides setscrew by turning it in a counter-clockwise direction using the
Hex key S5 (26) and remove setscrew away.
Insert the right / left side extension devices (36) in the mounts provided on both sides and
tighten the setscrew by Hex Key S5 (26).
11.11.1 Connection to AC power
High-voltage!
Only operate this machine in dry surroundings.
This machine may only be connected to a power source that fulfils the following
requirements (also see the section "Technical data"):
The mains voltage and the system frequency must conform to the voltage and frequency
that is indicated on the technical data sheet of the machine;
Fusing protection with a residual current device (RCD), protects all lines from short-circuits
and overloading.
Sockets must be properly installed, earthed and tested.
Position a power cable in such a way that it does not hinder the work and cannot be
damaged.
Protect the power cable against heat, aggressive fluids and sharp edges.
Only use rubber-coated extension cables with a sufficient wire cross-section (3 x 1.5
mm²).
Do not use the power cable for pulling the plug out of the socket.
12 OPERATIONS
This saw can be used as a:
Cross-cut saw/ miter saw
Table saw
Before making any changes in the settings of this machine, always remove
the plug from the socket.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWX07583 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWX07583 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWX07583

Varo POWX07583 User Manual - German - 17 pages

Varo POWX07583 User Manual - Dutch - 17 pages

Varo POWX07583 User Manual - French - 17 pages

Varo POWX07583 Additional guide - All languages - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info