756782
9
Zoom out
Zoom in
Previous page
1/16
Next page
POWX07583 EN
Copyright © 2021 VARO P a g e | 9 www.varo.com
10.2.1 Replacing the saw blade (Fig. 1)
Set the saw to crosscut and mitre saw mode.
Place the blade spanner on the outer flange and undo the saw blade screw (a) by turning
it in a clockwise direction using the Hex key S6. Remove the saw blade screw (a) and the
outer flange.
Remove the saw blade (18) from the inner flange carefully. Lift the lower blade guard (14)
upwards by pressing switch A,
Thoroughly clean the motor shaft and flange before you fit and secure the new saw blade.
Fit and fasten the new saw blade in reverse order.
WARNING: The work to change and align the saw blade must be carried out
correctly.
10.2.2 Mounting upper blade guard (Fig. 2)
Loose the two screws slightly by turning them in a counter-clockwise direction using the
Hex key S5.
Hold the upper blade guard (3) with one hand and the other hand hold the left lower metal
board (b).
Align the two sector gap on the metal board with two screws near the work-light, then
insert the metal board along the table liner slot.
Control the space between the knife Head and the metal board between 3~8 mm.
Tighten the two Screws by turning them in a clockwise direction using the Hex key S5
(26).
CAUTION: Controlling the space between the knife head and the metal
board can prevent the saw blade from cutting to the upper blade guard (3),
thus preventing accidents when operating the machine.
11 FUNCTIONS
11.1 Converting the saw from table to mitre saw for Cross-cut and mitre saw mode
(Fig.3)
Tighten the turntable locking knob (9) and beveling lock (16) by turning them clockwise.
Pull the motor locking pin (38), push down the upper table (1). Pull the saw mode locking
pin (22), then lift the saw table so that it moves into the highest position.
The saw has now been set to Cross-cut and mitre saw mode.
Switch A (8) and the trigger switch (20) are used for starting/stopping the mitre saw.
11.2 Converting the saw from mitre to table saw operating mode (Fig. 4)
Move the turntable to the 90° position, bevel angle at 90° position.
Tighten the turntable locking knob (9) and the beveling lock (16).
Hold the cutting handle (6) and press switch A (8)
Push down the cutting handle to the end and plug in the saw mode locking pin (22) at the
same time
Pull the motor locking pin (38), at the same time pull down the upper sawing table (1) to
the lowest position and release the locking pin (38) once the upper table is in the lowest
position.
The saw has now been set to table saw mode.
The ON/OFF switch (7) is used for starting/stopping the table saw.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWX07583 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWX07583 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWX07583

Varo POWX07583 User Manual - German - 17 pages

Varo POWX07583 User Manual - Dutch - 17 pages

Varo POWX07583 User Manual - French - 17 pages

Varo POWX07583 Additional guide - All languages - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info