756782
13
Zoom out
Zoom in
Previous page
1/16
Next page
POWX07583 EN
Copyright © 2021 VARO P a g e | 13 www.varo.com
Undo the bevel lock (16) and use the cutting handle (6) to tilt the machine head to the left
until it coincides with the required angle value.
Screw the bevel lock (16) back down again.
12.2 Table saw mode
12.2.1 ON/OFF switch (Fig. 17)
The saw can be switched on by pressing the green pushbutton (I). Wait for the blade (18)
to reach its maximum speed before starting the cut.
The red pushbutton (0) has to be pressed to switch off the saw.
12.2.2 Sawing (Fig. 18)
Undo the table parallel fence lock knob (5).
Set the table parallel fence (4) to the required dimension using the scale on the top saw
table and secure it with the locking knob (5).
Switch on the saw by pressing the green button (I).
Slide the work-piece slowly and precisely along the table parallel fence (4) to the saw
blade (18).
The upper blade guard (3) will open automatically and the work-piece moves forward.
Important: For work-piece widths below 120 mm a push stick (24) must be used in the
area near the saw blade (18). For work-piece widths below 30 mm a push stick (24) must
be used to move the work-piece.
After completing the cut, the upper blade guard (3) will close again automatically to cover
the saw blade (18).
Switch off the saw.
WARNING: The thickness of work-piece can’t overstep 50mm in table saw
mode.
NOTE: Check that the “table parallel fence” is locked in position and is
parallel to the saw blade. Check that riving knife is properly aligned with the
saw blade.
NOTE: Secure long work-pieces against falling off at the end of the cut, add
an additional support to prevent the remaining part from falling down to
cause accidental risk.
13 CLEANING AND MAINTENANCE
Attention! Before performing any work on the equipment, pull the power
plug.
13.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWX07583 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWX07583 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWX07583

Varo POWX07583 User Manual - German - 17 pages

Varo POWX07583 User Manual - Dutch - 17 pages

Varo POWX07583 User Manual - French - 17 pages

Varo POWX07583 Additional guide - All languages - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info