756782

Varo POWX07583 Manual

12
Zoom out
Zoom in
Previous page
1/16
Next page
POWX07583 EN
Copyright © 2021 VARO P a g e | 12 www.varo.com
12.1 Cross-cut sawing mode
12.1.1 Settings
When the bevel lock (16) is loosened, you can tilt the machine head to the left by up to
45°.
The turntable (11) can be adjusted from -45° to +45° by undoing the turntable locking knob
(9).
Start the saw by pressing the trigger switch (20) and switch A (8). The switch A (8) must
remain pressed during the sawing work.
12.1.2 Mitre 90° and turntable 90° (Fig. 13)
Important! Place the work-piece for sawing firmly on the machine surface and secure it
with the clamp (25) to prevent it from moving during the sawing process.
When you have switched on the saw, wait until the saw blade (18) has reached maximum
speed.
Press switch A (8) and trigger switch (20), using the cutting handle (6), apply steady and
light downward pressure to move the machine head through the work-piece.
After the cutting process is finished, bring the machine head back to its upper (home)
position and release trigger switch (20).
Important. The integral resetting springs will automatically lift the machine head.
Do not simply let go of the handle (6) after cutting, but allow the machine head to rise
slowly, applying slight counter pressure as it does so.
12.1.3 Mitre 90° and turntable 90°- 45° (Fig. 14)
The crosscut and mitre saw with table can be used to make right and left angular cuts of 90°-
45° in relation to the saw guide (21).
Move the machine head to its upper position.
Release the turntable (11) by slackening the turntable locking knob (9).
Set the turntable (11) to the desired angle, i.e. the marking on the turntable must coincide
with the desired angular setting on the base plate (1).
Retighten the turntable locking knob (9) to secure the turntable (11) in place.
12.1.4 Mitre cut 90°- 45° and turntable 90° (Fig. 15)
The crosscut and mitre saw with table can be used to make mitre cuts of 90° - 45° in relation
to the work face.
Move the machine head to its upper position.
Fasten the turntable (11) in 90° position.
Undo the bevel lock (16) and use the cutting handle (6) to tilt the machine head to the left
until the pointer coincides with the required angle value.
Retighten the bevel lock (16) and make the cut.
12.1.5 Mitre cut 90°- 45° and turntable 90°- 45° (Fig. 16)
The crosscut and mitre saw with table can be used to make mitre cuts to the left of 90°- 45° in
relation to the work face and, at the same time, 90° - 45° in relation to the saw guide (21)
(double mitre cut).
Move the machine head to its upper position.
Release the turntable (11) by slackening the turntable locking knob (9).
Adjust the turntable (11) to the angle required
Retighten the turntable locking knob (9) in order to secure the turntable in place.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWX07583 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWX07583 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWX07583

Varo POWX07583 User Manual - German - 17 pages

Varo POWX07583 User Manual - Dutch - 17 pages

Varo POWX07583 User Manual - French - 17 pages

Varo POWX07583 Additional guide - All languages - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info