631211
11
Zoom out
Zoom in
Previous page
1/44
Next page
Cut off the venting hose about 20mm below the vehicle floor
at a 45° angle relative to the direction of travel.
45º
20 mm
21
13
20
12
Fig. 11 Flexible hose installation
45º
20 mm
21
13
12
20
Ø 12 mm
Fig. 12 Rigid pipe installation
(e.g. John Guest System)
Manufacture a hose connection (22) for the cold water supply
between the drain valve (14) and the elbow fitting (13– lower
tube) at the boiler.
Route hot water supply line (23) from elbow fitting with built-
in aeration valve (12–upper tube) to hot water consumption
points.
If a water supply is being installed in the vehicle, it must
be ensured that sufficient room is left between the water
hoses and the heat source (e.g. heater, warm air duct).
SC hose clips (part no. 40712-01) are suitable for fastening
the hoses to walls or the floor. These hose clips also make it
possible to route water hoses on the heater’s warm air distri-
bution pipes to prevent freezing.
A water hose may only be routed at a distance of 1.5 m from
the heater at the warm air duct. The Truma SC hose clip can
be used for distances greater than this. With parallel routing
(e.g. through a wall) a spacer (e.g. insulation) must be fitted in
order to avoid contact.
Rigid duct installation using the John Guest
system
Truma can supply the water connections (12+13) and the
drain valve (14) with a diameter of 12mm as accessories. In
this case it is advisable to always use John Guest pipes, inser-
tion sleeves and locking rings.
Suitable adapters (not included in scope of delivery) must be
used for connecting rigid pipelines with a different diameter.
Route all water lines so they slope downwards to the
drain valve. Otherwise there is a risk of frost damage
that is not covered by the warranty!
Installing the drain valve
Fit drain valve(14) in an easily accessible location in the vicin-
ity of the boiler. Drill hole with diameter of 18mm and insert
the drainage socket with hose(15). Secure the drain valve in
place with 2screws. Water removal can take place directly to
the outside in a splash-protected location (fit splash guards if
necessary).
Ø 18 mm
14
15
Figure 9
Water line routing
Connect cold water supply(16) to drain valve(14). The direc-
tion of flow is irrelevant.
14
16
13
12
22
20
23
Figure 10
Push elbow fitting without aeration valve(13) as far as poss-
ible onto the boiler’s cold water connection tube (lower tube),
and push the elbow fitting with built-in aeration valve(12) as
far as possible onto the boiler’s hot water connection tube
(upper tube). Pull in the opposite direction to check that the
elbow fittings are securely attached.
Slide venting hose with an outer diameter of11mm (20) onto
the hose nozzle of the aeration valve (21) and route to the out-
side free of kinks. Radius of arc must not be less than 40 mm.
11
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma BGF 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma BGF 10 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 5,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Truma BGF 10

Truma BGF 10 User Manual - English, German, Dutch, Danish, French, Italian, Swedish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info