631211

Truma BGF 10 Manual

13
Zoom out
Zoom in
Previous page
1/44
Next page
12V electrical connection
Disconnect device from power supply before starting to work
on electrical components. Switching off at the control panel is
insufficient!
The device must be disconnected from the on-board power
supply when electric welding work is being carried out on the
vehicle body.
Reversing the polarity of the connections will result in
a risk of cable fire. Any warranty or liability claims will
also be invalidated.
Plug the control panel cable (28) with the connector (28a) into
the electronic control unit.
In order to attach it securely, route the control panel cable (28)
through the cable guide (28b).
The 12V electrical connection is made at the clamp (35).
orange = positive 12 V
blue = negative
This is done by pressing from above with a small screwdriver
and pushing the cable in from the front.
Connect to the fuse-protected on-board power supply (central
electrical system 5–10A) using a 2x1.5mm² cable.
Connect negative line to main ground connection. For lengths
of over 6m, use a 2 x 2.5 mm² cable. If the equipment is con-
nected directly to the battery, the positive and negative lines
must be protected.
If necessary, remove the outer cable sheathing at the cover
leadthrough.
No other 12V consumers must be connected to the supply
line.
The boiler fuse (36), 1.6 A (slow-acting), is on the electronic
control unit.
Screw on the cover (34).
28a
28b
28
35
34
36
Figure 15
When power packs or power supply units are being
used, note that the regulated output voltage is between
11V and 15V and the alternating current ripple is < 1.2Vpp.
Function check
The leak tightness of the gas supply line must be tested using
the pressure drop method after installation. A test certificate
must be issued.
Then check all device functions as described in the operat-
ing instructions – especially the boiler draining function. No
claims may be made under the warranty for damage
caused by frost!
Never operate the boiler when it is empty. An electrical
function check can be carried out briefly even if there is no
water in the boiler. Always follow the operating instructions
before starting up.
Warnings
The installer or vehicle owner must affix the yellow sticker
with the warning information, which is enclosed with the ap-
pliance, in a location in the vehicle where it is clearly visible
to all users (e.g. the wardrobe door). Missing stickers can be
requested from Truma.
13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Truma BGF 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Truma BGF 10 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 5,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Truma BGF 10

Truma BGF 10 User Manual - English, German, Dutch, Danish, French, Italian, Swedish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info