756407
9
Zoom out
Zoom in
Previous page
1/12
Next page
EN 9
pyrometer TP10
5. Press the Mode button(3) to return to the measurement
value display.
Info
The device memorizes the selected setting when
switching off.
Switching the laser pointer on or off
Ex works the laser pointer is switched off.
Info
Please observe that with a switched-on laser the laser
pointer will go on as soon as you press the
Measurement button(7) or activate continuous
measurement.
Warning of laser radiation
Class 2 laser radiation.
Lasers of class 2 only radiate in the visible range and
during continuous wave operation (lasting beam) no
more than 1 milliwatt (mW) of output will be emitted.
Looking directly into the laser beam for a longer period
of time (more than 0.25seconds) can cause damage to
the retina.
Avoid looking directly into the laser beam. Never look
into the laser beam using optical aides. Do not
suppress the winking reflex when looking into the laser
beam unintentionally. Never point the laser beam at
people or animals.
1. Repeatedly press the Mode button(3) until the Lit Laser
menu is displayed.
2. Press the F3button(2).
ðThe Laser indication(13) appears on the display.
ðThe laser pointer is active and will switch on when
starting with the next measurement.
3. Press the F3 button(2) again.
ðThe Laser indication(13) disappears.
ðThe laser pointer is switched off.
Info
The device memorizes the selected setting when
switching off.
Setting the alarm
The device is equipped with an alarm function for which an
upper and a lower alarm threshold can be specified. When
exceeding or falling below these values, an acoustic signal will
be emitted. Additionally, the display lights up in one of the
following colours:
Display colour Meaning
Flashes red Surface temperature exceeds
activated upper threshold. The
display flashes red and a
constant alarm tone is emitted.
Also works when the display
illumination is deactivated.
Flashes blue Surface temperature below
activated lower threshold. The
display flashes blue and a
constant alarm tone is emitted.
Also works when the display
illumination is deactivated.
Continuously illuminated in
green
Surface temperature is in
normal range. The display will
only be illuminated in green if
the display illumination is
activated.
Setting the lower alarm threshold:
1. Repeatedly press the Mode button(3) until the Hi Set Lo
menu is displayed:
2. Press the F3 button(2) to set the lower alarm threshold.
ðThe On menu will be displayed.
ðThe current value for the lower alarm threshold appears
on the display.
3. Press the F2 button(5) to enable (On) or disable (Off) the
lower alarm threshold.
ðWith enabled lower alarm threshold the indication
Lo(17) will be displayed.
4. Either press F3 or F1 to set the value.
ðFor larger temperature changes hold onto these buttons,
as needed.
5. Press the Mode button(3) to return to the measurement
value display.
ðThe setting for the lower alarm threshold is saved.
Setting the upper alarm threshold:
1. Repeatedly press the Mode button(3) until the Hi Set Lo
menu is displayed.
2. Press the F1 button(4) to set the upper alarm threshold.
ðThe On menu will be displayed.
ðThe current value for the upper alarm threshold appears
on the display.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec TP10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec TP10 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec TP10

Trotec TP10 User Manual - German - 13 pages

Trotec TP10 User Manual - Dutch - 13 pages

Trotec TP10 User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info