756407
7
Zoom out
Zoom in
Previous page
1/12
Next page
EN 7
pyrometer TP10
Operation
Inserting the battery
Note
Make sure that the surface of the device is dry and the
device is switched off.
27
28
1. Open the battery compartment by folding open the
cover(28) with your fingers.
2. Use the battery clip(27) to connect the new
battery(1x 9V) with correct polarity.
3. Insert the battery in the battery compartment.
4. Close the cover of the battery compartment(28).
Carrying out a measurement
Ensure that the surface to be measured is free of dust, dirt
or similar substances.
To be able to gain exact measurement results on surfaces
which reflect heavily, stick matt masking tape to the
surface or apply matt black paint with a very high and
known degree of emission.
Note the 75:1 ratio of the distance to the measuring spot
diameter. For accurate measurements the measuring
object should be at least twice as large as the measuring
spot.
Please proceed as follows to carry out a measurement:
1. Point the device at the object to be measured.
2. Press the measurement button(7). Hold onto the
Measurement button(7) if you want to perform a
prolonged measurement.
ðThe device turns on and carries out a measurement.
ðThe SCAN symbol(12) appears in the display. The
currently measured value is indicated.
3. Let go of the Measurement button(7) again.
ðThe device stops measuring. The HOLD symbol(12)
appears in the display.
ðDepending on the setting of the device, either the
Max/Min value or the Avg/Dif value of the last
measurement will be displayed.
Settings
The bottom line of the display contains a three-part menu.
Within this menu different settings can be selected. You can
switch through the different menus using the Mode button(3).
Menu example:
MxMn Save Avg
The menu is controlled as follows:
The F1 button(4) selects the function on the left, MxMn in
our example.
The F2 button(5) selects the function in the centre, Save in
our example.
The F3 button(2) selects the function on the right, Avg in
our example.
Setting the Max/Min function
1. Repeatedly press the Mode button(3) until the MxMn Save
Avg menu is displayed:
ðThe MxMn Save Avg menu is shown on the display.
2. Press the F1 button(4) to select MxMn.
ðThe maximum value is displayed in the upper
measurement value display(18).
ðThe minimum value is displayed in the lower
measurement value display(20).
ðThe discrepancy between the current measured value
and the minimum value is indicated as deflection on the
scale(21).
Setting the Avg/Dif function
Please bear in mind, that the average value is continually
determined anew during a measurement, which means that
there can be deviations of the displayed Dif value in the in the
hundredth °C range.
1. Repeatedly press the Mode button(3) until the MxMn Save
Avg menu is displayed.
2. Press the F3 button(2) to select Avg.
ðThe average value is displayed in the upper
measurement value display(18).
ðThe difference between the current measured value to
the average value is displayed in the lower
measurement value display(20).
ðThe difference between the current measured value to
the average value is indicated on the scale(21).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trotec TP10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trotec TP10 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Trotec TP10

Trotec TP10 User Manual - German - 13 pages

Trotec TP10 User Manual - Dutch - 13 pages

Trotec TP10 User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info