618948

Trebs PastaGusto Model 21126 Manual

12
Zoom out
Zoom in
Previous page
1/47
Next page
When you open the appliance for the first time, you will find the following accessories:
- a ring spanner
- a plastic knife that can also be used as a scraper
- a cleaning attachment
- ten different pasta-shaping attachments
Your pasta machine is supplied fully assembled by the manufacturer. Carefully follow the instructions
given below for the installation and dismantling of the appliance.
DISMANTLING INSTRUCTIONS
1. Check to ensure that the pasta machine is not connected to the mains.
2. Remove the locking washer (11) together with the pasta attachment. If necessary, use the ring
spanner for this purpose.
3. Carefully remove the dough transport coil (10). If after use, the back of the coil is full of sticky dough,
first dismantle the coil according to the following instructions. You can remove the coil by lightly
tapping the end of the shaft and then removing the same.
4. Pull the closing slide (3) fully out of the appliance by gently pushing the locking button located above
the closing slide.
5. Press the unlocking button (4) for the cover, located on the front side of the cover (5) on the mixing
container (8) downwards by pulling it gently forward and lift the cover.
6. The unlocking button (7) for removing the mixing container (8) is located on the hinging side of the
cover near the casing (1).
7. Press the unlocking button and remove the mixing container.
8. Pull the chrome-plated drive shaft of the stirring mechanism (6) outward and remove it from the mixing
container.
9. Now carefully clean all the components that come into contact with the dough, either by hand or in the
dishwasher (*please read the instructions on the first page).
INSTALLATION INSTRUCTIONS
1. First check to ensure that the pasta machine is not connected to the mains.
2. Place the stirring mechanism (6) in the mixing container (8) with the largest opening facing the front
of the mixing container.
3. Place the stirring mechanism (6) in such a manner that the openings in the shaft of the stirring
mechanism coincide with the openings in the container.
4. Insert the chrome-plated drive shafts with the groove in the topmost drive opening of the motor
casing (1).
5. Press the unlocking button (7) on the motor casing downwards and push the mixing container (8)
together with the stirring mechanism over the chrome-plated drive shaft into the motor casing. It may
be necessary to turn the stirring mechanism (6) to some extent, so that everything falls properly in
place. Now unscrew the unlocking button (7) and check whether the locking has taken place properly
by carefully pulling the mixing container.
6. Push the closing slide (3) in the groove of the casing (on/off switch (2)) fully into the mixing position.
This is the position in which the closing slide is pushed as far as possible into the casing.
7. Push the dough transport coil (10) into the extrusion chamber (9) until it is in the hexagonal opening
of the motor casing (1). By carefully rotating the dough transport coil, it will come to rest in the proper
place, so that it will not project outside the threaded part of the extrusion chamber.
8. Select the desired pasta-shaping attachment and place it in the extrusion chamber (9), so that the
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Trebs PastaGusto Model 21126 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Trebs PastaGusto Model 21126 in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 1,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info