485545
35
Zoom out
Zoom in
Previous page
1/42
Next page
35
REPLACING THE LAMP / CLEANING THE PROJECTOR
Holder
(b)
(a)
Exhaust vent
Intake vent
ENTER
WIDETELE
LAMP
TEMP
MENU/EXIT
POWER
button
button
POWER button
5 Holding the holder, pull out the light-source
lamp from the unit.
Pull out the light-source lamp slowly. If the lamp is burst, the glass
fragments may be scattered if the lamp is pulled out hurriedly.
Do not spray water or the like over the light-source lamp pulled
out, or do not put it where children can access it or near anything
easily flammable. It may cause burn or injury.
6 Holding the holder of a new lamp, insert the
lamp to the bottom fitting the lamp to the
shape of the hole in the unit.
7 Press the holder into the storage.
Make sure that the holder is securely locked.
8 Securely screw down the three fixing screws
(b) with the Phillips screwdriver.
9 Insert the lamp cover into the unit, and se-
curely screw down the screw (a) with the
Phillips screwdriver to fix the lamp cover.
If the lamp cover is dislocated, the power can not be turned on.
10
Turn on the power.
11
Simultaneously press on
{{
{{
{,
}}
}}
} buttons and
POWER button ( ) on the operation panel of
the unit for more than 3 seconds.
If the three buttons are not pressed simultaneously, the lamp-used-
hours may not be reset.
If the lamp-used-hours have exceeded 1500 hours and the lamp has been replaced, it is not possible to turn on
the new light-source lamp until the lamp-used-hours are reset.
Do not reset the lamp-used-hours if the lamp is not replaced.
Cleaning dust in the intake vent
If dust is accumulated in the intake vent, the temperature in the projec-
tor goes up abnormally, and may
damage the internal parts. Also, the light-source lamp may come off to
protect the internal parts. Clean up
the dust with a vacuum cleaner about once a year.
Cleaning the projector
Softly wipe off dirt on the projector with a soft cloth.
If the dirt is thick, wipe it off with a cloth soaked in a neutral detergent diluted with water, and then finish with a dry
cloth.
If any pesticide is sprayed over the projector, or if the projector is wiped with benzine or thinner, or if rubber or
vinyl products are brought into contact with the projector for a long period of time, the painting of the projector
may change in quality or removed.
Cleaning the lens
Remove dust or dirt on the lens with a commercially available lens cleaning kit (blower, brush, and the
like).
Because the surface of the lens is easily scratched, do not rub or hit the surface with anything hard.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba MT500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba MT500 in the language / languages: English as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info