485545
36
Zoom out
Zoom in
Previous page
1/42
Next page
36
POWER
LAMP TEMP Countermeasure
On in orange
Off
Off
Off Off
Off
Off
Off
On in red
On in redOn in
green
Connect the power cable to the projector.
Plug the power plug into a power outlet.
Turn On the main power switch.
Fit the rear lamp cover.
If the projector itself is very hot, turn off the power switch, and
after the temperature has come down, turn on the power switch again.
Replace the light-source lamp. (The lamp is at the end of its life.)
If the intake and/or exhaust vent is blocked with anything, remove it.
Prevent the wind from a heater from blowing into the exhaust
vent of the projector, if it is happening.
Check if the air filter is foul with dust or not.
Clean the filter, if it is foul.
Press POWER button after POWER indicator has stopped
blinking in orange.
If the main power was turned Off while the fan was still turning, the lamp may not be able
to come on next time for about one minute after the main power switch is turned On .
For about one minute after the light-source lamp has been put out, it is not possible to put the lamp on again.
Blinking in
orange
TROUBLESHOOTING
Before asking for repair of the projector, check the followings: If the problem still continues, stop using
it and be sure to unplug the power plug. Then, contact the delivery agent of the projector.
Picture images are not projected on screen.
Phenomenon
Power can not be turned
on.
Picture images are not
projected on screen.
Projected images sud-
denly disappear.
Check/Countermeasure
Check whether the indicators are on or off and how they are lighting.
In some cases it takes about one minute to put the lamp on.
On rare occasions, the lamp fails to come on. Then, turn on the lamp again after a few minutes.
If the projector finished operation without sufficient cooling, the cooling fan is turning and the follow-
ing operation of the main power button may not work after the main power was turned on. (At this
time POWER indicator blinks in orange.) After the fan has stopped turning, press the power button
again to turn on the indicator in orange.
Check if the intake vent is not blocked with anything.
Check to be sure that the lamp cover is closed. (See Page 32 and 33.)
Check if the cable connecting the projector and external equipment is not broken.
When an extension cable is used, replace it with the attached cable for checking. If picture images
are normally projected with the attached cable, employ an RGB signal amplifier together with the
extension cable.
This phenomenon may occur if the intake vent and/or exhaust vent is blocked with any-
thing.
(At this time TEMP (temperature) indicator is lighting in red.)
After removing those things blocking the intake vent and/or exhaust vent, execute the
followings:
1 Wait until the intake/exhaust fan stops turning. (Wait until TEMP (temperature) indica-
tor comes off.)
2 Turn off the main power switch.
3 Wait about 10 minutes.
4 Turn on the main power switch.
5 Press POWER button.
LAMP indicator lighting in red indicates that the lamp must be replaced. Replace the
light-source lamp to a new one. (See Page 32 and 33.)
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba MT500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba MT500 in the language / languages: English as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info