485545
37
Zoom out
Zoom in
Previous page
1/42
Next page
37
TROUBLESHOOTING
Projected images are irregular.
Others
Phenomenon
Power can not be
turned on.
If the following phenomenon occurs after the lamp has been replaced, check the following first:
Phenomenon
Projected images are distorted.
Projected images are
dark.
Projected images are
blurred.
White dots are seen in
projected images.
Black dots are seen in
the projected images.
A rainbow-color brume pattern
is seen on projected images.
Fine streak pattern is seen
on projected images.
Projected images are
disturbed.
Tint of projected images
is irregular.
Check/Countermeasure
Adjust the projector and the screen so that they may become perpendicular to each other. (See Page 11.)
Adjust BRIGHT and CONTRAST in the picture quality menu. (See Page 28.)
Replace the lamp to a new one. (See Page 32 and 33.)
Adjust the focus. (See Page 18 and 22.)
Check if the lens cap is not put on.
Clean the lens.
Adjust FINE and DIVIDING RATIO in the signal setting menu. (See Page 30.)
Adjust BRIGHT and CONTRAST in the picture quality menu. (See Page 28.)
Adjust the projector and the screen so that they may become perpendicular to each other.
(See Page 11.)
This phenomenon is proper to DLP projector and is not a failure. (A very small number of
pixels may be constantly lighting on or off, but this is not a failure. Pixels of more than
99.99% are effective ones.)
This pattern is a color breaking noise that occurs in DLP system in principle. This is not a
failure.
This phenomenon occurs due to the interference with the screen surface, and is not a
failure. Try to replace the screen or defocus the lens a little.
Securely plug the cable connecting the external equipment to the bottom.
Keep the projector away from equipment generating interfering radiowaves.
Check if the cable connecting the external equipment is broken.
Phenomenon
A hot air comes out of
the exhaust vent.
Menu setting is dis-
abled.
Abnormal sounds oc-
cur.
Check/Countermeasure
This air comes out after cooling the inside of the projector. It may feel hot, but is not a
failure.
Affected by noises, the microcomputer in the projector may be malfunctioning.
>Turn off POWER once, and after 2 minutes turn it on again.
If POWER can not be turned off, turn off the main power switch and leave the projector as
it is for more than 10 minutes. Then, turn on POWER again.
On rare occasions, a metallic clank occurs because the color wheel is rotating at a high
speed. But, this is not a failure.
Check/Countermeasure
Securely fit the rear lamp cover. (See Page 32 and 33.)
Reset the lamp-used-hours. (See Page 33.)
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Toshiba MT500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Toshiba MT500 in the language / languages: English as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info