658793
18
Zoom out
Zoom in
Previous page
1/30
Next page
P14
MAIN MENU
After you have adjusted the settings for the preferred scan process, move to Scan selected satellite with
pq and then select the search method with tu.
You can select between following procedures:
Scan selected satellite Scanning the selected satellite.
Search All Sat Scanning the selected satellite.*
Search TP Scanning the selected transponder.
Network Search NIT scanning the selected satellite.
Load HD Austria Senderliste:
Here the “HD Austria Senderliste” can be installed subsequently. In this case,
previously installed or available channels are retained and sorted in the “HD
Austria Senderliste” accordingly. TV or radio channels which are not included in
the “HD Austria Senderliste” are ranked above channel number 4000 or 6000 and
can still be edited.
When all settings have been made, press OK at the preferred scan method to start this scan process or
to quit without scanning. All newly found channels will be stored at the end of the channel list.
*Only available if more than one satellite has been setup.
NOTE: NIT (Network Identification Table): This option will scan on the NIT table of the satellite and
allows you to receive new appeared channels. Please consider that unlike Astra 19.2 und HOT
BIRD 13° some satellites do not offer this function. Please check with your local dealer.
NOTE: When you want to add technical data for a new transponder we recommend verifying it
by consulting websites like: www.lyngsat.com or www.kingofsat.net or you can refer to
professional journals.
7.1.3 System Settings
Use the System Settings menu to configure settings for language, audio, video, look and feel of your
receiver. Choose a setting with pq and press OK to list the possibilities or use tu to change the value of
the highlighted setting. Please also read the displayed instructions for each screen carefully. They will help
you to adjust the settings correctly and easily.
Language: Here you can change the language for the On-Screen-Display, use tu to select
your preferred language. It affects the menu language of your receiver so all
menus and messages will be displayed in the chosen language.
Video Setting: Select the connection to your TV set. Either Scart or HDMI can be selected via
tu. Press OK at the used connection to open the settings for it. For details, see
chapter 7.1.3.1 HDMI or 7.1.3.2 SCART.
Audio Output: Here you can adjust the settings for your digital audio output. Press tu to
choose between BitStream and PCM. If a device that can decode Dolby Digital is
connected, use the setting BitStream. If this is not possible, use PCM.
Audio language: Press OK to open the setting. The most important audio languages are displayed.
For details, see chapter 7.1.3.3 Select Audio Language.
Subtitle Setting Press OK to open this setting. For details, see chapter 7.1.3.4 Select Subtitle
Language
Start up channel In this menu you can select your start up channel. Select Last watched if your TV
shall start with the last viewed channel before the receiver switched off. To switch
on with a specific channel, select Fixed Channel by pressing tu. Press OK and
OK again to continue. Press pq or P+/P to scroll in the list and confirm your
selection with OK.
Banner display time: Defines the time for displaying the information banner. Press tu to choose
between 1 sec ~ 20 sec.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson THS811 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson THS811 in the language / languages: English as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Thomson THS811

Thomson THS811 User Manual - German - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info