636719

Texas BCU33M Manual

14
Zoom out
Zoom in
Previous page
1/18
Next page
14
Brush cutter and Grass trimmer
• When the engine is stopped the rotating blade must be held in grass or bush until it holds still.
• Always hold the machine with both hands.
• The machine must not be used if the safety guard is not correctly fitted and in mint condition.
• Always stop the engine before attempting to remove objects that may have stuck on the blade.
• Never touch or try to stop the blade while it is still spinning.
• A rotating blade may cause damage, as it continues to spin after the engine has stopped or the gas
has been turned off. Always be in control of the tool until the blade has stopped spinning.
• Always make sure that the blade is mounted securely and correctly before every time it is used.
• Only use a sharp blade. Replace blades that are worn or damaged.
• Only use original spare parts.
• Only use the blade for weeds, grass and similar.
• Kickback is something that may occur when the rotating blade gets into contact with something, it
cannot cut. This contact may have the effect, that the blade stops for a moment, and suddenly the
tool is thrown away from the hard object that was hitting. This reaction may be so violent that the
user loses control of the tool. Kickback may occur without warning if the blade is stuck, loses speed
or impeded. This is most likely in areas where it is difficult to see the material that is being cut.
• The harness must always be used and adjusted to fit in the correct manner.
• Keep a firm grip on both handles while the blade is running. Keep the blade away from your body
and below your waist.
Changing from trimmer to brush cutter
Dismounting the trimmer head See Fig 4B
1. Fit the Allen key (2) in the hole of the gear (3) to lock the gear in place.
2. Turn and remove the trimmer head (1) from the shaft.
3. Washers can now be removed.
Notice: Keep the parts for the trimmer head together for later use.
Mounting of blade. See Fig 4A
1. Fit the Allen key (2) in the hole of the gear (3) to lock the gear in place.
2. Fit the washer (7), blade (1), washer (6) and the holder (5) onto the axle.
3. Fit the nut (4). Fasten tightly anticlockwise. Make sure the blade is securely fasten.
Changing from brush cutter to trimmer
Dismounting the blade See Fig 4A
1. Fit the Allen key (2) in the hole of the gear (3) to lock the gear in place.
2. Loosen and remove the nut (4) that fastens the blade.
3. Washers, holder and blade can now be removed.
Notice: Keep the parts for the blade together for later use
Mounting of trimmer head. See Fig 4B
1. Fit the Allen key (2) in the hole of the gear (3) to lock the gear in place.
2. Fit the washers (4+6)
3. Mount the trimmer head (1) onto the shaft, turn it in place and make sure it is securely fasten.
Replacement the trimmer cord
Fig.5
1. Press on each side of the line compartment. The lid may now be removed.
2. Dismount the roll simply by pulling it. Leave the spring on the spool. Remove any bits of line.
3. Take 3-4 meters of new line (2,4 mm) and place it double in a loop-
4. Fit the loop in the middle of the spool and wind the nylon lines around the spool in each groove
without twisting the line. Follow the direction of the arrows from bottom of the spool.
Do not overfill the spool!
5. Mount the line compartment in reverse order. First, fit the spring into its position. Then place the line
in the two metal mortises of the line compartment.
6. Mount the lid. Ensure that it is fitted securely. Cut of excess nylon line.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Texas BCU33M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Texas BCU33M in the language / languages: English, Danish as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info