617907
95
Zoom out
Zoom in
Previous page
1/132
Next page
TASCAM HS-2 95
Frame Type
Set the time code frame type of the currently loaded
project.
Setting buttons:
23.976F
,
24F
,
25F
,
29.97DF
(default),
29.97ND
,
30DF
,
30ND
I/O page
Set the synchronization signal status display and time
code output on this page.
NOTE
If the Option SY-2 has not been installed, the display is
shaded and the setting cannot be selected.
STATUS
This shows the status of synchronization signals.
TIMECODE IN:
When time code is input, the time code frame rate is
shown.
WORD/VIDEO IN:
When a synchronization signal is detected at this
connector,
WORD
,
VIDEO
or
TriLevel
is shown.
TC Out Mode
Use the buttons to set the time code output mode.
GenOut button:
Time code is output from the internal time code
generator.
PlayOut button (default):
In timeline mode, the time code time for playback and
recording is output. In take and playlist modes during
playback, the time code recorded in the file is output.
Remote settings (REMOTE SETUP)
Make settings for the PARALLEL, RS-232C, RS-422 and
Ethernet (Network) connectors.
The
REMOTE SETUP
screen has 5 pages:
GENERAL
,
PARALLEL
,
RS-232C
,
RS-422
and
ETHERNET
. Touch
the tabs at the bottom of the screen to open the corre-
sponding page.
GENERAL page
Make the external remote controller settings on this page.
FADER MODE
Allows the fader on an external TASCAM RC-HS20PD
remote controller (sold separately) to be enabled or
disabled. When set to
Disable
, the internal fader is fixed
at 0 dB.
Setting buttons:
Disable
,
Enable
(default)
FADER Start MODE
When the fader start function of an external TASCAM
RC-HS20PD remote controller (sold separately), for
example, is on, set whether fader starts, which allows
you to start playback by raising the fader from when in
playback standby, is enabled or not.
Setting buttons:
Disable
,
Enable
(Default)
FADER Stop MODE
When the fader start function of an external TASCAM
RC-HS20PD remote controller (sold separately), for
example, is on, set whether fader stop, which allows you
to put playback into standby by lowering the fader to
during playback standby, is enabled or not.
Setting buttons:
Disable
,
Enable
(Default)
NOTE
If both the
FADER Start MODE
and
FADER Stop MODE
items are set to
Disable
, the fader start function of the
external TASCAM RC-HS20PD remote controller (sold
separately) will be turned off automatically, and the
FADER START indicator will turn off. In this state, if you
touch the Fader Start key on the TASCAM RC-HS20PD
remote controller, a
Cannot Change Now. Fixed in
current mode
warning appears in a pop-up window.
10–Internal settings
95


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam HS-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam HS-2 in the language / languages: English as an attachment in your email.

The manual is 4,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info