161727
23
Zoom out
Zoom in
Previous page
1/32
Next page
1-Introduction
TASCAM CD-RW900 23
5−Recording
Advanced recording
Fade-in and fade-out recording
At the beginning and end of recording, fade-in and
fade-out effects can be performed.
1 During stop or recording standby mode, set the op-
eration using the following menu options on the REC
sub-menu (refer to “Operation basics” on page 14).
FADE IN?
The length of the fade in to the normal level can be
set between 1 and 30 seconds in 1-second incre-
ments (default setting: 3 seconds).
FADE OUT?
The length of the fade out into complete silence
can be set between 1 and 30 seconds in 1-second
incre-ments (default setting: 3 seconds).
The display shows
Fade Out>XXs
or
Fade In>XXs
.
2 In recording standby mode, press the FADER key
on the remote control.
Recording begins and the sound fades in. After the
preset fade-in time, the sound is at normal level.
3 During recording, press the FADER key on the re-
mote control when you wish to fade-out the sound.
Fade-out begins with
Fade Out
ashing on the dis-
play then the unit enters recording standby mode.
4 Press the STOP key and the PMA writing will begin.
NOTE
Fade-in or fade-out function can be operated only
pressing the FADER key on the remote control unit.
Synchronized recording basically means that recording
will begin automatically when a signal is received, and
will stop when the signal ends.
Use the SYNC REC key to select the synchronization
mode. The synchronization mode determines the auto-
mated start and stopping of recording when a signal is
received.
During stop or recording stancby mode, repeated
presses of this key cycle through the fol-lowing modes:
Sync ALL: The
SYNC
indicator lights up.
Sync 1: The unit stops when a selected track is n-
ished and the
SYNC
indicator ashes
Sync OFF: Turns Sync recording function off
After the synchronization mode is selected, the record
ready mode must then be entered (you cannot reverse
the order of these steps).
Starting playback of the source automatically starts re-
cording on the CD-RW900 if Sync ALL or Sync 1 has
been selected (see “Sync recording” below) and manual
record start is disabled. If Sync OFF is selected, the re-
cording must be started manually.
Synchronaized recording
Sync recording
1 While recording standby mode, press the SYNC
REC key repeatedly to select Sync ALL or Sync 1.
2 Set the signal detection threshold level. Use the
SYNC LEVEL option in the REC sub-menu (refer to
“Operation basics” on page 14).
Rotate the MULTI JOG dial to adjust the level. The
level can be set from -72 dB to -24 dB in 6 dB incre-
ments. The default setting is -24 dB.
Press the MENU key or push the MULTI JOG dial to
enter and return to recording standby mode.
3 Input the source signal.
Recording begins automatically when the source
signal is detected. The source signal should be high-
er than the adjusted threshold level.
NOTE
After the mode is set, more than one second of
signal under the adjusted threshold level is required
to start recording automatically, otherwise, the unit
does not begin recording even it detects the signals.
Start of recording
level
time
Noise level
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam cdrw900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam cdrw900 in the language / languages: English as an attachment in your email.

The manual is 2,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info