161727

Tascam cdrw900 Manual

21
Zoom out
Zoom in
Previous page
1/32
Next page
1-Introduction
TASCAM CD-RW900 21
5−Recording
The sampling frequency for CDs is 44.1 kHz. The CD-
RW900 will always record (and play back) CDs at this
frequency.
However, if recording through a digital connection
(either coaxial or optical) and the source has been re-
corded at a frequency other than 44.1 kHz, or is being
played back at a non-standard speed using a varispeed
unit (more than 1% away from the standard), the CD-
RW900’s internal frequency converter: SRC (Sampling
rate convertor) will automatically convert the incoming
frequency to 44.1 kHz.
To set the SRC
Press the MENU key and select the SRC? option in
the REC sub-menu (refer to “Operation basics” on
page 14).
Rotate the MULTI JOG dial and select ON.
Press the MENU key or push the MULTI JOG dial to
enter and return to normal mode.
NOTE
When the SRC function is off, receiving digital signals,
the display shows the REC indicator ashing while re-
cording or recording standby mode.
The digital signals other than 44.1kHz cannot be re-
corded when SRC is off. The error message
Not
Fs44.1k!
will appear on the display.
Frequency conversion
Before you start recording using the CD-RW900, make
sure that you understand the following key points:
≠
Once you have recorded on a CD-R disc, the data
cannot be erased from it.
≠
You can add tracks to an unnalized recordable
disc. Once nalized, a CD-R disc is “xed” and
behaves in the same way as a pre-recorded disc.
Finalized CD-RW discs, however, can be erased, re-
freshed and re-recorded.
Input selection
To select the input to be recorded, press the INPUT
SELECT key on the main unit.
Repeated presses of the key cycle through the follow-
ing options:
ANALOG Analog
OPTICAL Optical digital in
COAXIAL Coaxial digital in
In the case of either the coaxial or optical inputs being
selected, the appropriate indicator:
COAXIAL
or
OPTI-
CAL
, lights on the right of the screen.
If the analog signal is selected, the
ANALOG
indicator
lights on the right of the screen.
Analog recording level The level of the analog signals
received at the ANALOG IN jacks are controlled with
the INPUT controls.
When recording analog signals, set the digital volume to
0 dB.
Digital recording level The level of the digital signal
may be controlled using the digital volume menu, as de-
scribed below.
1 Call up the
VOLUME
option in the REC sub-menu
(refer to “Operation basics” on page 14).
Push the MULTI JOG dial to enter the function on.
2 Rotate the MULTI JOG dial to adjust the input vol-
ume between -54dB and +18 dB (relative to the
original input level).
There is also a -
‹
setting which represents a com-
plete signal cut. The display shows
Vol> ---dB
for
the -
‹
setting.
3 Press the MENU key or push the MULTI JOG dial to
enter the setting and return to normal mode.
Input monitoring
When the unit is in record ready, or record mode, the
input signal is output from the OUT jacks (digital and
analog), allowing you to hear the input signal.
1 Press the RECORD key on the front panel or the re-
mote control when a recordable disc is not inserted.
The word
Monitor
appears on the display to show
that the output signal is an echo of the input signal(s).
2 Exit the monitor mode by using the STOP key.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam cdrw900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam cdrw900 in the language / languages: English as an attachment in your email.

The manual is 2,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info