Manual SureFlap Microchip Cat Flap - serie nr 2000000 plus (page 8 of 146) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish)

782757

Zoom out

Zoom in

1/146

13 14

accessory

Fitting your cat flap in glass

Tools and supplies required

Ruler

Glazier

Cat Flap Mounting Adaptor

The screws and screw caps provided

Cross head screwdriver

Clear all-weather sealant

Step-by-step guide for cutting the hole in glass

Place one of the mounting adaptors (it doesn’t matter which)

over the tunnel of the cat flap so that the side with the sealant is

facing outwards and is not touching any surfaces.

When working with cut glass always wear protective gloves as the edges may be sharp.

Next, slide the external frame over the tunnel. Using a cross

head screwdriver and the screws you selected previously, secure

the external frame in place. Fasten the first screw until it is

secure, but not too tight, then do the same to the last one. Once

all the screws are secure, tighten them.

Before you begin, we advise that you program your cat(s) ID prior to fitting, see page 7.

Take this height and add 56mm (2 '') to it, this will give

you the total distance from the floor to the centre of the

circle you need cutting. Make sure this point is at least

200mm (7 '') from the bottom of the window frame to

allow room for the mounting adaptor.

H= cat’s tummy height + 56mm = the centre of the circle.

212mm

If you are fitting in a double or triple glazed unit, the

glazier should use a non-metallic spacer bar around the

hole, as a metal spacer could aect the cat flap's ability

to read microchips. (The spacer bar is needed to fill the

gap between the panes of glass.)

Step-by-step guide for fitting

We advise that there are two people present for glass fitting;

one person inside the house and one outside. Firstly, apply a

strip of clear all-weather sealant to the back of both mounting

adaptors, about 15mm ('') from the edge. Make sure your cat

flap is nearby and ready to be fitted.

From the outside of the house, take the second mounting

adaptor and slide it over the tunnel with the sealant facing the

window. You may need the person on the inside of the house to

keep pressure on the cat flap to make sure it stays in place.

From inside the house, put the tunnel through the hole in the

glass, making sure the cat flap is positioned centrally within the

hole. Press firmly on both the cat flap and the mounting adaptor

so that you compress the sealant against the glass. Remember

the SureFlap logo must be inside the house.

Installation video tutorials (English speaking) can be found at surepetcare.com/support

7Now, insert the two screw caps into the external frame.

Firstly, to select the correct length of screw from the sets

provided, you need to compare the screw lengths to the

thickness of your door. The screw length needs to be between

20 to 35mm (/ to 2 '') longer than the thickness of the

glass.

20 to 35mm

To fit your cat flap into glass, you will require a circular

hole to be cut measuring 212 mm (8 '') in diameter.

This will need to be done by a professional glazier. To

ensure your cat has unhindered access through the cat

flap, you will need to make sure that this circular hole is

cut at the appropriate height. Do this by first measuring

the height from your cat’s tummy to the floor.

If you do not have a hole in your glass door to fit the cat flap you will need to contact a

glazier to visit your home and measure up for the new pane of glass. In most cases it is not

possible to cut a pane of glass in situ, especially if you have a double or triple glazed unit.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of SureFlap Microchip Cat Flap - serie nr 2000000 plus in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13.72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

SureFlap Microchip Cat Flap - serie nr 2000000 plus Manual

Product: