Manual SureFlap Microchip Cat Flap - serie nr 2000000 plus (page 10 of 146) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish)

782757

Zoom out

Zoom in

1/146

Fitting your cat flap in a wall

Tunnel

External screw holes

External frame Internal screw holes

Behind the battery

compartment cover

Front frame

Internal screw holes

Behind the internal screw covers

Wall mounting

screw holes

Wall fitting features

Installation video tutorials can be found at surepetcare.com/support

Before you begin

Please contact a qualified builder to discuss the best location to fit your cat flap.

Remember some walls can be structural or there may be electrical wires, gas or water

pipes hidden within them which, if damaged, can cause serious problems.

We recommend that you do not attempt the work yourself unless you have relevant

experience. The job will be messy so protective clothing and eye-wear is a must and when

using power tools, please follow all safety instructions provided.

accessory

Tools and supplies required

Cat Flap Tunnel Extenders

Electric drill & masonry bits

Protective clothing & eye-wear

Appropriate power tools for your wall

All-weather tape

Wall plugs & screws

Cross head screwdriver

Clear all-weather sealant

Ruler

Blu tack

Sharp pencil

Vacuum cleaner

For wall installations, tunnel extenders can be stacked together to create a longer tunnel for

the Cat Flap. The existing tunnel is 70mm (2 ”) long. Each tunnel extender adds 50mm (2”) to

the length of the tunnel.

Step-by-step guide

To ensure your cat has unhindered access through the cat

flap, measure the height from their tummy to the floor. Mark

this height on your wall, as this is where the bottom of the

hole should be cut through the wall. Note: If there is a large

drop on the outside of the house you will need to place a

step outside for your pet to access the tunnel.

Before you begin, we advise that you program your cat(s) ID prior to fitting, see page 7.

Now, from the outside of your house, use the drilled hole as a

reference and stick the external frame to the wall. We advise

that you stick the external frame a few millimetres lower

than the inside to allow for any rain collected in the tunnel

to run back outside.

Back on the inside of the house; whether you are cutting

through brick, wood, tiles or plaster, you should drill some

pilot holes, firstly around the perimeter of the line you have

drawn and then in the middle of the marked area. The holes

around the perimeter should be touching the inside of

the line and the holes in the centre should go all the way

through the wall to help with the cutting process.

Stick the external frame to the wall using the mark you made for

the height of your cat’s tummy to align the bottom edge of the

hole. Use a spirit level to ensure the frame is level, then run a

sharp pencil around the inside edge of the frame. Now mark the

centre of the drawn area, this will be used as a reference point.

Before you start to cut the hole remove the cat flap from the

area to minimise the amount of dust the product is subjected to.

Attach a ball of Blu Tack (or similar adhesive putty) to each

rear corner of the external frame so that you can stick it to the

wall and use it as a template.

Using the appropriate power tool and drill bit for your wall

(please consult a builder to identify the appropriate tools),

drill a hole all the way through the wall at the centre point

you marked. We advise you have somebody assisting you

with a vacuum cleaner, so as not to fill the room with dust.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of SureFlap Microchip Cat Flap - serie nr 2000000 plus in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13.72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

SureFlap Microchip Cat Flap - serie nr 2000000 plus Manual

Product: