Manual SureFlap Microchip Cat Flap - serie nr 2000000 plus (page 7 of 146) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish)

782757

Zoom out

Zoom in

1/146

11 12

Fitting your cat flap in wood or plastic

Tools and supplies required

Ruler

Spirit level

Blu Tack

Electric drill with a 6mm ('') drill bit

Cross head screwdriver

The screws and caps provided

Sharp pencil

Electric jigsaw

Protective eye-wear

Step-by-step guide

Stick the external frame to the door using the mark you made

for the height of your cat’s tummy to align the bottom edge of

the hole. Use a spirit level to ensure the frame is level, then run

a sharp pencil around the inside edge of the frame.

Put the cat flap back through the door and slide the external

frame over the tunnel. Holding the product firmly in place, use a

cross head screwdriver and the screws you selected previously,

to attach the external frame. Fasten the first screw until it is

secure, but not too tight, then do the same to the last one. Once

all the screws are secure, tighten them.

Now, insert the two screw caps into the external frame.

To ensure your cat has unhindered access through the cat flap,

measure the height from their tummy to the floor. Mark this

height on your door, as this is where the bottom of the hole

should be cut through the door.

Attach a ball of Blu Tack (or similar adhesive putty) to each rear

corner of the external frame so that you can stick it to the door

and use it as a template.

Once the main hole is cut, check whether there is any metal within your door. If you can

see metal, go to page 15 and follow the instructions for fitting in a metal door.

Now check that the cat flap fits through the hole. Remember

the SureFlap logo must be inside the house. We advise that you

have two people for this, one inside the house and one outside

to help hold the product firmly in place.

Using the jigsaw, cut around the outer edge of the line

you have marked. By doing this, the cat flap should fit

through the hole first time. However, if you cut on, or

inside the line, the hole is likely to be too small. If this is the

case, please take the time to carefully file the hole until the cat

flap fits through easily.

When using power tools, please follow all safety instructions provided with the product.

Installation video tutorials (English speaking) can be found at surepetcare.com/support

Before you begin, we advise that you program your cat(s) ID prior to fitting, see page 7. On the outside of the house, make sure the tunnel of the cat flap

is securely pushed through the hole and then slide the external

frame over it. When the external frame is in place, using a

sharp pencil mark through the two holes.

Now it’s time to prepare for cutting. We strongly advise

that you drill large holes in all the corners of the outline to

make it easier to cut the hole with a jigsaw. Make sure these

holes are touching the line and that they are big enough for

the blade of the jigsaw to fit through.

To choose the correct length of screw, from the sets provided

you need to compare the screw lengths to the thickness of your

door. The screw needs to be between 15 to 30mm ( to 1 '')

longer than the thickness of your door.

15 to 30mm

Remove the external frame and the cat flap from the door

then drill the two screw holes using a 6mm (/'') drill bit,

remembering to hold the drill horizontally. We recommend that

you choose the correct length of screw to attach the cat flap to

your door at this stage. See the next step.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of SureFlap Microchip Cat Flap - serie nr 2000000 plus in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13.72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

SureFlap Microchip Cat Flap - serie nr 2000000 plus Manual

Product: