650849

Superrollo RM10MM Manual

23
Zoom out
Zoom in
Previous page
1/68
Next page
Starting up
the device
23
If SW40 winding shafts with exterior fold are used, attaching clips are additionally
required.
¾ 1. Approx. every 40 cm, slide an attaching clip (1) over the winding shaft (2)
from above.
¾ 2. Insert the securing springs (4) into the rectangular holes in the attaching clips
(3).
1 3
4
2
1. 2.
Setting the terminal points
Setting the terminal points defines the upper and lower terminal positions for
raising and lowering the roller shutter. These settings can be subsequently
changed at any time.
The tubular motor is designed for short-term operation (four minutes). In
order to avoid damage due to heating, the motor shuts off automatically
on exceeding this period of time or in the event of frequent switching.
Allow the motor to cool for approx. 20 minutes in this case.
ATTENTION
Malfunctions due to missing or incorrect terminal point settings.
¾ Make sure that the device is only used with correctly set terminal
points.
The adjuster screws are located on the tubular motor's driving head.
¾ Use the upper screw (1) to set the lower terminal point.
¾ Use the lower screw (2) to set the upper terminal point.
1
2
¾ In order to extend the travel, turn the screw in the PLUS direction.
¾ In order to shorten the travel, turn the screw in the opposite direction (MINUS).
The direction of rotation of the adjuster screws may vary depending on
the model. Pay attention to the labelling on the driving head.
ATTENTION
Damage to the device due to roller shutter curtain shortening as
a result of temperature fluctuations.
¾ Set the terminal points so that the roller shutter curtain stoppers
have approx. 2-3 cm clearance from the limit stops.
Proceed as follows to set the upper terminal point:
¾ Operate the motor to raise the roller shutter.
If the motor stops before the desired terminal point is reached, proceed as follows:
¾ Leave the timer or the switch set to the raise position.
¾ Use the adjustment tool to carefully turn the lower adjuster screw in the PLUS
direction until the motor has reached the desired terminal point.
If the motor passes by the desired terminal point, proceed as follows:
¾ Stop the motor.
¾ Operate the motor to lower the roller shutter.
¾ Stop beneath the desired terminal point.
¾ Use the adjustment tool to carefully turn the lower adjuster screw in the MINUS
direction.
¾ Operate the motor to raise the roller shutter in order to check the terminal point
which has now been set.
¾ If necessary, repeat the steps described above until the desired terminal point
is reached.
Proceed as follows to set the lower terminal point:
¾ Operate the motor to lower the roller shutter.
If the motor stops before the desired terminal point is reached, proceed as follows:
¾ Leave the timer or the switch set to the lower position.
¾ Use the adjustment tool to carefully turn the upper adjuster screw in the PLUS
direction until the motor has reached the desired terminal point.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Superrollo RM10MM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Superrollo RM10MM in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 5,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info