480560
16
Zoom out
Zoom in
Previous page
1/27
Next page
PART 2 • English
13
English
6.3.1 Language Setting
In this menu you can set your language of chioce for menu, audio and subtitles.
OSD Language: Use t/u to select menu language.
Audio Language: Digital TV allows transmitting more than one audio track/
language. If a channel has multiple audio tracks/languages,
the receiver will select the suitable audio track/language
automatically according to your selection.
Subtitle Language: This setting allows you to define the subtitle language. Use t/u
to select a subtitle language and the receiver will display the
subtitles in this language automatically (if available). If you do not
want to display subtitles, then adjust the setting to Off.
NOTE: Subtitles will be displayed when available. Availability depends on the
local broadcast.
Please also consider that events may contain “built in” subtitles which can’t be disabled.
6.3.2 Output Setting
In this menu you can set the output parameters of the receiver according to the connected TV set
and for the connected audio amplifier if applicable.
TV Mode: Use t/u to select the mode. Commonly the PAL standard is
used, but it might be that you need to use the setting NTSC. We
recommend referring to the user manual of your TV set to check
the correct setting.
Video Output: Use t/u to select between RGB and CVBS modes.
Screen Mode: Use t/u to adjust this setting in accordance with the aspect
ratio of your TV set (4:3 or 16:9) and the preferred conversion.
The options are: Auto (automatic detection of aspect ratio), 4:3
Panscan (displays 16:9 broadcasts full screen and cut upper and
lower parts of 16:9 video on your 4:3 TV), 4:3 letterbox (displays
16:9 widescreen broadcasts with black bars on top and under the
picture on a 4:3 TV). For a modern 16:9 TV set following options
can be set: 16:9 Wide Screen, 16:9 PillarBox (4:3 broadcasts will be
shown with black vertical bars on the left and right side of the
image) and 16:9 Pan&Scan. We recommend trying these settings
in order to find the option that suits you best. Do not forget
about the possibility to control the TV format via the menu of
your TV set.
HDMI Output: Allows you to change the resolution of the HDMI output. If the
connected TV does not support the set resolution you will see a
black screen. In this case, wait for 10-15 seconds without pressing
any buttons on the remote control of the receiver, and the
previous value will be recovered automatically.
Loop out in stand-by: This allows to by-pass the antenna signal to the ANT OUT
connector, where you may have an additional TV set/receiver
connected, in order to receive analogue/digital broadcasts there
too.
Digital audio: Use t/u to adjust this setting in accordance to the used audio
equipment. To loop the digital audio through HDMI or S/PDIF to
a connected amplifier, home theatre or other equipment able to
decode AAC and AC3, set RAW HDMI ON.
If neither your TV set nor any other connected audio equipment support decoding AAC and AC3,
adjust RAW HDMI OFF.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 8525 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 8525 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info