480560
15
Zoom out
Zoom in
Previous page
1/27
Next page
PART 2 • English
12
6.2 Channel search
In the menu Channel Search you can adjust your search settings and perform an automatic or
manual channel search. Press MENU and use t/u to select Channel Search, then press OK.
Following submenus will be displayed: Search Setup, Auto Search and Manual Search.
Use p/q to select a submenu and press OK or u to access.
6.2.1 Search Setup
In the menu Search setup you can set the antenna power and the country in which you live.
Country: Use the t/u buttons to change the country.
Antenna Power: If you use an antenna that can be amplied (i.e. an active indoor/
outdoor antenna) and it requires a voltage of 5 V and doesnt consume
more than 60 mA, then you can set the antenna power to On. If you use
an antenna without an amplier or your antenna is already amplified
by an external power supply or if you use an antenna from a house
distribution system, please keep the antenna power O.
6.2.2 Auto Search
After selecting this menu item and pressing OK you will be asked to enter the PIN code DEFAULT
PIN: 0000 in order to update the current channel list. If you don’t want to perform a full channel
scan you can press EXIT to cancel. After entering the PIN code DEFAULT PIN: 0000 the receiver
will perform an automatic channel search through all frequencies and after finishing this process it
will update the channel list. During the search process the receiver will display the progress bar, the
currently scanned frequency and the channel names. The receiver will add all new found channels
to the channel list.
6.2.3 Manual search
In this menu you can search for channels on a specific frequency or channel. This menu requires
knowledge of some parameters in order to search on the correct channel/frequency in your area.
Scan mode: Use t/u to choose between By Channel and By Frequency.
If you set the scan mode By Channel, then the following is available:
Band: Use t/u to choose UHF (Ultra High Frequency) or VHF (Very High
Frequency).
Frequency channel: Select a frequency channel on which you would like to search for
the channels.
If you set the scan mode By Frequency, then the following is available:
Frequency: Use 09 to enter the frequency on which you would like to search
for channels.
Band: For the VHF frequency band commonly used 7 MHz, for UHF
frequency 8 MHz is used.
Signal level and quality indicators will help you ensure that you have signal on the selected
frequency channel or frequency entered, as well as to adjust the antenna, if necessary.
After you have entered the settings correctly you will need to select Search (directly above the
signal bars) and press OK. The receiver will start to search for channels and if available with your
entered parameters, they will be added to the channel list. If you don’t get a satisfying result after
the search process, please contact the local service or check reliable websites/magazines if the
entered values are correct.
6.3 System Setup
Press MENU and use t/u to select System Setup, then press OK. Following submenus will be
displayed: Language Setting, Output Setting, Time Setting, Auto Standby, Parental Guidance and Reset
Factory default.
Use p/q to select the desired submenu and press OK or u to access.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 8525 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 8525 in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info