480574
9
Zoom out
Zoom in
Previous page
1/27
Next page
PART 1 • English
6
1. Open the cover
2. Install batteries
3. Close the cover
NOTE: The batteries should not be recharged, disassembled, electrically short-circuited, be
mixed or used with other types of batteries.
2.6 Using the Remote Control
Fig. 5
To use the remote control, point it towards the front of the digital receiver. The remote control has a
range of up to 7 metres from the receiver, if properly aligned towards the IR eye on the front panel.
The remote control will not operate if its path is blocked.
NOTE: Sunlight or very bright light (such as TL lighting) might decrease the sensitivity of the
remote control.
3.0 CONNECTIONS
3.1 Basic connection using a Scart cable
Fig. 6
A. Connect the LNB of your satellite antenna to the SAT IN connector of your
receiver using a good quality coax cable and suitable ‘F-connector’ plugs.
B. Connect one end of a good quality Scart cable to the TV SCART connector on
your receiver and the other end to the SCART input of your TV.
C. Plug the power cord to a suitable wall outlet.
3.2 Basic connection using an HDMI cable
Fig. 7
A. Connect the LNB of your satellite antenna to the SAT IN connector of your
receiver using a good quality coax cable and suitable ‘F-connector’ plugs.
B. Connect one end of a good quality HDMI cable to the HDMI output on your
receiver and the other end to the HDMI input of your TV.
C. Plug the power cord to a suitable wall outlet.
3.3 Connecting multiple fixed LNBs using a DiSEqC 1.0 switch
Fig. 8
A. Connect the LNBs of your fixed antenna to the inputs of a DiSEqC 1.0 switch
B. Connect the output or “to receiver” connector of the DiSEqC 1.0 switch to the
SAT IN connector on your receiver.
C. Refer to section 3.1 or 3.2 for TV and mains connections.
4.0 FIRST TIME INSTALLATION
After all connections have been made properly, switch on your TV and make sure the receiver is
connected to the main power. If you are using the receiver for the first time or restored to factory
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7002 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info