480574
10
Zoom out
Zoom in
Previous page
1/27
Next page
English
PART 1 • English
7
default, the First Installation menu will appear on your TV screen. Use the tu buttons to select the OSD
Language of your preference and press OK to confirm. An Info page will be displayed. Read the info guide
and press the INFO button to proceed to the next Installation step. You can open and close the info page
again by using the INFO button.
NOTE: If German is selected as language, German preset channels from ASTRA 19.2E will
be installed. You can continue with the Installation menu to scan and install further
channels as described below or directly go to viewing mode by pressing the EXIT button
twice to start enjoying the pre-installed channels immediately.
4.1 Installation
4.1.1 Satellite Selection
Use pq to highlight the satellite your dish is aimed at. When using a multi feed antenna with more
than 1 LNB, select the satellites your antenna is adjusted for by pressing the OK button and set the
appropriate LNBs in the DiSEqC point. The scan process will then search on all selected satellites.
4.1.2 Signal Adjust
The signal quality bar on the bottom of the screen allows you to fine tune the alignment of your antenna
for optimum reception. Adjust your antenna for maximum possible signal quality. When the signal
cannot be improved anymore, fix the dish on this position and press the BLUE button for Scan.
4.1.3 Scan Mode
Use pq tu to highlight the options of choice and press OK to start the Channel Search. It is
recommended to use the default settings.
4.1.4 Channel Search
Your receiver will now perform an automatic channel search. When the process has been completed, all
found channels will be stored and the receiver will switch to the first found channel. You are now ready to
enjoy your new receiver.
NOTE: If no channels were found during the automatic channel scan, the receiver will return to
the First Installation menu. Please select your language again and refer to chapter 7.3
for further instructions.
5.0 QUICK GUIDE FOR USING YOUR RECEIVER
We at STRONG understand that you can’t wait to enjoy your new HD receiver. The following quick guide
will make you familiar with the basic operation of this device. We do, however, advice you to read the full
manual to get the best performance from your STRONG HD receiver.
To turn your receiver ON or to Standby, use the q button on the remote control.
Choose channels with the pq buttons. Alternatively, you can also enter the channel number with the
0~9 buttons on the remote control or press OK in viewing mode to display the channel list.
The volume can be adjusted with the tu buttons.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7002 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info