608703
258
Zoom out
Zoom in
Previous page
1/858
Next page
12
EN
ENGLISH
(Translation of the Original Instructions)
Tightening the screws to a torque over
25 Nm, will damaged the seat.
If the connectors are not connected the
machine will not work.
5.2.3 Bellows installation (7)
1. Fasten the seat in place with the two screws
(7:B).
2. Position the bellows (7:A).
3. Secure the bellows in place with the 10 pegs
(7:C).
5.2.4 Install the carrier (8)
Install the carrier (8:B) on the back of the seat
(8:A) using the 4 screws (8:C).
5.3 STEERING WHEEL (9)
1. Push the steering wheel sleeve (9:A) all the
way down the steering column (9:B) .
2. Align the holes on the sleeve with those on
the steering column.
3. Once the holes have been aligned (9:C), in-
sert the two pins (9;D).
5.4 TOW BAR (10)
Install the tow bar (10:A) on the rear of the machi-
ne.
Use the screws and nuts (10:B; 10:C).
Tightening torque: 22 Nm.
5.5 QUICK-RELEASE SUPPORTS (1:P)
The quick-release supports and relative installa-
tion instructions are supplied in a separate box
inside the machine packaging.
Install the quick-release supports on the machi-
ne’s front axles.
5.6 BATTERY CHARGING
The battery must be fully charged befo-

Please refer to 99.8 for the battery char-
ging procedure.
5.7 TYRE PRESSURE
For the tyre pressure, please refer to “0 TECHNI-

5.8 ACCESSORIES
For installation of accessories, see the installation
guide accompanying each accessory.
Note: In this case the cutting means as-
sembly is considered an accessory..
6 COMMANDS AND CONTROL
INSTRUMENTS
6.1 BONNET (11)
The bonnet can be opened as follows:
1. Turn the two screws through 90° (11:A)
2. Pull the handle up (11:B) while at the same
time carefully lifting the bonnet (11:C).
3. To close the bonnet, gently push down on it,
if necessary, until the handle engages (11:B).
Turn the two screws through 90° (11:A).
It is prohibited to start the engine when
the bonnet is open.
6.2 MAIN POWER KEY SWITCH (12)
The electrical power supply is activated by a key
(12:A). This can be found under the bonnet (1:H)
consequently to get to the main power switch you
must rst open the bonnet (see 6.1).
Insert the key (12:A) in the main power switch,
press it in and turn it to the right to switch on the
electrical system’s power supply.
Turn the key to the left to turn the power supply o.
The key can be removed from the
switch only when it is turned to the left.
6.3 PARKING BRAKE PEDAL (13:A)
Never partially press the pedal while
driving. There is a risk of overheating
the power transmission.
The pedal (13:A) has the following three positions:
Released. Traction is engaged.
The parking brake is not
activated.
Pressed right down. Forward
drive disengaged. The parking
brake is fully activated but not
locked. This poasition is also
used as an emergency brake.
6.4 PARKING BRAKE LOCKING LEVER
(13:B)
The lever locks the “clutch-brake” pedal in
the pressed right down position. This fun-
ction is used to lock the machine on slopes,
during transport, etc., when the engine is
not running.
258


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga Pro 740 IOX - P 901 PH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga Pro 740 IOX - P 901 PH in the language / languages: All languages as an attachment in your email.

The manual is 160,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info