Manual Stiga Pro 740 IOX - P 901 PH (page 257 of 858) (All languages)

608703

257

Zoom out

Zoom in

1/858

ENGLISH

(Translation of the Original Instructions)

machine securely with ropes or chains

to the hauling device.

3.6 ENVIRONMENTAL PROTECTION

• Safeguarding the environment must be a re-

levant and priority aspect of machine use, of

benet to the community and the environment

we live in. Avoid being a disturbance to the

neighbourhood.

• Adhere strictly to the local regulations gover-

ning the disposal of packaging, oil, fuel, lters,

damaged parts or any other element which

may have an impact on the environment; this

waste should not be disposed of along with

standard household waste, but must be dispo-

sed of separately and sent to special waste

disposal facilities for handling and recycling.

• Adhere strictly to local regulations governing

the disposal of cuttings.

• When the machine is withdrawn from service,

do not dump it in the environment, but take it to

a waste disposal facility in accordance with the

local regulations in force.

4 INSURING YOUR LAWNMOWER

Check the insurance on your lawnmower.

Contact your insurance company.

You ought to have fully comprehensive insurance

for trac, re, damage and theft.

5 ASSEMBLY

Do not use the machine until all the in-



section have been carried out.

Unpacking and completing the as-

sembly should be done on a at and

stable surface, with enough space for

machine handling and its packaging,

always making use of suitable equip-

ment.

5.1 ASSEMBLY COMPONENTS (3)

The machine is delivered with the seat, armrests,

steering wheel, tow bar, quick-t supports disman-

tled. The battery is in its housing and connected.

The packaging holds the components needed for

assembly (3) as listed in the table below:

Pos. N. Descrizione Dimensione

A 2 Spring pin 6 x 36

B 2 Key for switch /

C 1 Key for main power switch /

D 2 Armrests /

E 4 Screws for seat fastening M8 x 20

F 10 Pegs for bellows fastening

G 4 Bushes for seat fastening

H 4 Split lock washer M8

L 4 Hex head screw M8 x 40

M 1 Carrier

N 4 Pan head Torx screw M6 x 20

O 1 Tow bar

P 2 Flanged nut M8

Q 2 Hex head screw M8 x 20

R 2 Quick-release supports

5.2 SEAT (6)

Install the seat following the instruc-

tions in the following order.

5.2.1 Armrest assembly (6)

You will nd the armrests and the components for

their installation in a separate box in the machine

packaging.

Install as follows:

1. Fit the left support (6:A) and the right support

on the seat. Use 3 screw (5:6), (provided) on

each side.

2. Secure the arm rests in place using the

screws (6:C), nuts (6:D) and spacers (6:E).

3. Tighten the screws just enough to be able to

lower/lift the armrests easily.

5.2.2 Seat assembly

1. Smear oil over the 4 sliding runners (5:A).

2. Prepare the 4 screws (M8 x 40) by inserting

them in the spring lock washers and bushes.

See (5:B).

3. Lift the seat support (5:C) to an upright po-

sition.

4. Bring the seat towards the support and insert

the peg in the slot (5:D) on the support.

5. Make sure the seat is right up against the

support and position it so that the holes for

the xing screws are about halfway along the

sliding runners.

6. Insert and tighten the 4 screws (5:B).

7. Fasten the screws, tightening torque 20÷25

Nm.

8. Connect the seat connector (5:E) to the wiring

connector (5:F).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga Pro 740 IOX - P 901 PH in the language / languages: All languages as an attachment in your email.

The manual is 160,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga Pro 740 IOX - P 901 PH Manual

Product: