Manual Stiga ESTATE 3084 H (page 69 of 118) (English, German, Dutch, French, Italian)

608479

69

Zoom out

Zoom in

Previous page

1/118

Next page

11

Mechanical transmission

Push the pedal down as far as possible (see

4.21) and move the gear change lever into

1st gear (see 4.22).

Keep the pedal pressed down and disen-

gage the parking brake. Slowly release

the pedal which will turn from «brake» to

«clutch», thus operating the rear wheels

(see 4.21).

WARNING! The pedal has to be re-

leased gradually, as a sudden engage-

ment may cause the vehicle to tip over

and the driver to lose control.

Gradually reach the desired speed using

the throttle and gear lever. To change gear,

press the clutch halfway down (see 4.21).

Hydrostatic transmission

Disengage the parking brake and release

the brake pedal (see 4.31).

Press the drive pedal (see 4.32) in direction

«F» and reach the required speed by pro-

gressively increasing pressure on the pedal

and moving the accelerator.

WARNING! Drive must be engaged

as described below (see 4.32) to prevent

sudden engagement from causing tipping

up and loss of control of the vehicle, par-

ticularly on slopes.

5.4.3 Braking

First reduce the machine’s speed by reducing

the engine’s r.p.m., and then press the brake

pedal (see 4.21 or 4.31) to slow down the ma-

chine until it stops.

Hydrostatic transmission

The machine already slows down consider-

ably by just releasing the drive pedal.

5.4.4 Reverse

IMPORTANT Reverse must only be engaged

when the machine has stopped.

IMPORTANT To proceed in reverse gear with

the cutting means engaged, it is necessary to

press and hold the consent button (see 4.9) so

as not to cause the engine to stop.

Mechanical transmission

Press the pedal until the machine stops and

then switch into reverse by shifting the lever

sideways and into position «R» (see 4.22).

Gradually release the pedal to engage the

clutch and then begin moving in reverse.

Hydrostatic transmission

When the machine is stopped, start the re-

verse movement by pressing the drive pedal

in the «R» direction (see 4.32).

5.4.5 Grass cutting

(Fig. 5.8) Adjust the position of the anti-chipping

wheels (1-if tted) whose function is to reduce

the risk of tearing up sections of lawn, which can

occur when the edge of the cutting means as-

sembly drags over irregular ground.

The three dierent heights of the front wheels

allow you to maintain a safe distance «A» be-

tween the cutting means assembly and the

ground.

To change position, unscrew the nut (2) and ex-

tract the pin (3).

Reposition the wheel (1) to the desired position,

then reassemble the pin (3), making sure the pin

(3) head is facing toward the inside of the ma-

chine; then tighten the nut completely.

WARNING! This should always be per-

formed on both wheels, positioning them at

the same height WITH THE ENGINE OFF AND

CUTTING MEANS DISENGAGED.

To start cutting:

– move the throttle to «FAST»;

– bring the cutting-means assembly to the high-

est position;

– engage the cutting means (see 4.5) only on

grass lawns; avoid engaging them on stony

ground or when the grass is very high;

– start moving forwards on the grass very

slowly and with utmost caution, as already

described;

– regulate the cutting height and speed (see

4.6) considering the conditions of the lawn

(the height, density and dampness of the

grass).

WARNING! When cutting on sloping

ground, the forward speed must be reduced

to ensure safe conditions (see 1A – C7-8-9).

1

the mower wont go into mowing drive when I lift the button
Submitted on 7-3-2023 at 06:09
Reply Report abuse
The engine cuts out if the forward pedal is pushed down.. it is not the seat cut out or the grass catcter off Submitted on 23-12-2022 at 01:10
Reply Report abuse
I need information on replacing the Deck cutting belt Submitted on 28-5-2020 at 15:47
Reply Report abuse
my stiga 3084H , with the wheels straight , the steering wheel is no longer aligned .The steering rods don't appear to be bent. Could the steering cog have jumped a tooth on the rack?
Dave Submitted on 8-12-2018 at 20:29
Reply Report abuse
HELP My stiga estate 3084h mower starts without having to press the foot brake and occasionally stops after a few seconds then it will not start leave it for a couple of minutes and it will start I have changed all the safety micro switches but it is still the same any suggestions please
Thank you in advance Submitted on 2-7-2018 at 08:44
Reply Report abuse
How do I level the cutting deck, it is 20mm higher on one side Submitted on 4-9-2017 at 16:25
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Stiga ESTATE 3084 H at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga ESTATE 3084 H in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stiga ESTATE 3084 H

Stiga ESTATE 3084 H User Manual - Danish, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 192 pages

Stiga ESTATE 3084 H Additional guide - All languages - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info