Manual Stiga ESTATE 3084 H (page 67 of 118) (English, German, Dutch, French, Italian)

608479

67

Zoom out

Zoom in

Previous page

1/118

Next page

9

WARNING! Reverse must be en-

gaged when the machine has stopped.

Hydrostatic transmission

4.31 BRAKE PEDAL (Fig. 4.3 no.31)

This pedal works the brake on the rear

wheels.

4.32 CLUTCH PEDAL (Fig. 4.3 no.32)

This pedal engages drive in the wheels and

controls the machine’s forward and reverse

speed.

– To engage forward gear just press it in the

«F» direction with the tip of your foot, not-

ing that increasing the pressure on the

pedal progressively increases the speed

of the machine.

– Reverse is engaged by pressing the pedal

with the heel towards «R».

– The pedal automatically goes into neutral

«N» when released.

WARNING! Reverse must be en-

gaged when the machine has stopped.

NOTE If the drive pedal is used, wheth-

er forwards or for reverse, when the parking

brake (4.4) is engaged, the engine stops.

4.33 HYDROSTATIC TRANSMISSION

DISENGAGEMENT LEVER

(Fig. 4.3 no.33)

This lever has two positions as shown on the

label:

«A» = Transmission engaged: for all

uses, when moving and during cut-

ting;

«B» = Transmission disengaged:

this makes it much easier to move

the machine by hand, with the en-

gine turned o.

IMPORTANT To avoid damaging the

transmission unit, this operation must be car-

ried out only when the engine has stopped

with the pedal (4.32) at position «N».

5. OPERATING INSTRUCTIONS

5.1 SAFETY RECOMMENDATIONS

WARNING! If the machine is likely to

be used mostly on sloping ground (never

steeper than 10°), fit counterweights (sup-

plied on request (see 8.6) beneath the

cross-member of the front wheels. These

improve stability at the front and reduce the

chances of tipping over.

IMPORTANT All the references relating to

the positions of controls are those described in

chapter 4.

5.2 WHY THE SAFETY DEVICES CUT IN

The safety devices work in two ways:

– they prevent the engine from starting if all the

safety requirements have not been met;

– by stopping the engine if even just one of the

safety requirements is lacking.

a) To start the engine, it is necessary that:

– the transmission is in “neutral”;

– all the safety devices are correctly in place;

– the operator is seated;

b) The engine stops when:

– the operator leaves his seat;

– the grass catcher is lifted or the rear dis-

charge guard removed without disengaging

the cutting means;

– the parking brake is engaged without disen-

gaging the cutting means;

– the speed change is activated (see 4.22) or

the drive pedal (see 4.32) with the parking

brake on.

5.3 PRELIMINARY OPERATIONS BEFORE

STARTING WORK

Before starting to mow, it is necessary to carry

out several checks and operations to ensure

you can work eciently and in maximum safety.

5.3.1 Seat adjustment (Fig. 5.1)

To change the seat position, loosen the four x-

ing bolts (1) and slide it along the slots.

Once you have found the right position, tighten

the four screws (1) thoroughly.

5.3.2 Tyre pressure (Fig. 5.2)

Having the right tyre pressure is the main condi-

tion for ensuring that the cutting-means assem-

bly is horizontal and mows evenly.

Unscrew the valve caps and connect a com-

pressed air line with a gauge to the valves and

adjust the pressure to the indicated values.

5.3.3 Filling with oil and fuel

NOTE The type of oil and fuel to use is given

1

the mower wont go into mowing drive when I lift the button
Submitted on 7-3-2023 at 06:09
Reply Report abuse
The engine cuts out if the forward pedal is pushed down.. it is not the seat cut out or the grass catcter off Submitted on 23-12-2022 at 01:10
Reply Report abuse
I need information on replacing the Deck cutting belt Submitted on 28-5-2020 at 15:47
Reply Report abuse
my stiga 3084H , with the wheels straight , the steering wheel is no longer aligned .The steering rods don't appear to be bent. Could the steering cog have jumped a tooth on the rack?
Dave Submitted on 8-12-2018 at 20:29
Reply Report abuse
HELP My stiga estate 3084h mower starts without having to press the foot brake and occasionally stops after a few seconds then it will not start leave it for a couple of minutes and it will start I have changed all the safety micro switches but it is still the same any suggestions please
Thank you in advance Submitted on 2-7-2018 at 08:44
Reply Report abuse
How do I level the cutting deck, it is 20mm higher on one side Submitted on 4-9-2017 at 16:25
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Stiga ESTATE 3084 H at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga ESTATE 3084 H in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stiga ESTATE 3084 H

Stiga ESTATE 3084 H User Manual - Danish, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 192 pages

Stiga ESTATE 3084 H Additional guide - All languages - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info