608664

Stiga 740 WX - P 901 CH Manual

165
Zoom out
Zoom in
Previous page
1/588
Next page
For the type of oil to use please refer to
“0 TECHNICAL DATA TABLE”.
Use oil with no additives.
Change the oil when the engine is warm.
        
     -
quently allow the engine to cool down
for a few minutes before proceeding to

Proceed as follows:
1. Place the machine on a at surface.
2. Put the parking brake on.
3. Open the bonnet.
4. Grab the clamp on the oil drain hose. Use
polygrip pliers or similar (21:A; 22:A).
5. Move the clamp 3-4 cm up the oil drain hose
and pull out the plug.
6. Collect the oil in a suitable vessel.
NOTE! Take care not to spill any oil on
the drive belts.
7. Hand the spent oil over to a disposal facility
in accordance with local provisions.
8. Replace the oil drain plug and move the
clamp back over the plug.
9. Clean up any spills.
10. Remove the dipstick and ll with fresh oil. For
the quantities of oil required, please refer to
"0 TECHNICAL DATA TABLE”.
11. After lling up the oil, start the engine and
leave it to idle for 30 seconds.
12. Check there are no oil leaks.
13. Stop the engine. Wait for 30 seconds and
then check the oil level again as indicated in
heading 9.5.1.
9.5.3 
For the frequency of this intervention
see chapter 13.
First drain the engine oil and insert the oil drain
plug as described above. Then replace the oil lter
as follows:
• Clean the area around the lter and
dismantle the lter.
• Smear the gasket on the new lter with oil.
• Install the lter. First screw in the lter so
that the gasket comes into contact with the
engine. Then screw in the lter a further
1/2-3/4 turn.
• Continue with point 7 in accordance with
the indications provided in 9.5.2.
9.6 REPLACING THE FUEL FILTER (21:B,
22:B)
For this maintenance operation, see
also the manual for the engine supplied
with the machine.
For the frequency of this intervention
see chapter 13.
Check for fuel leaks once the new lter has been
installed.
9.7 CHECKING/TOPPING UP THE
TRANSMISSION FLUID [4WD]
For the frequency of this intervention
see chapter 13.
-
quired, please refer to "0 TECHNICAL
DATA TABLE”.
9.7.1 Check/top-up (25)
1. Place the machine on a at surface.
2. Read the uid level in the reservoir (25:A).
The level should match the line.
3. Top up if necessary.
9.7.2 Change

1. Run the machine at variable speeds for 10-
20 minutes to heat up the transmission uid.
2. Place the machine on a at surface.
3. Put the parking brake on.
4. Take the disengagement levers to position
A1 - B1 as illustrated in g.(15:A; 15:B).
5. Place a container under the rear axle and
another one under the front axle.
6. Open the bonnet and remove the plug on the
uid reservoir.
Only a 3/8” square drive may be used
for the oil plug. Other tools may damage
the plug.
7. Remove the uid drain plug from the rear
axle (26:A).
8. Remove the 2 drain plugs on the front axle.
Use a 12 mm tubular wrench. Allow the uid
in the front axle and pipes to drain out (27).
9. Check that the gaskets on the drain plugs
of the front axle are intact (27). Replace the
plugs. Tightening torque: 15-17 Nm.
10. Check that the gasket on the drain plug of
the rear axle is intact (26:A). Replace the
EN
ENGLISH
(Translation of the Original Instructions)
19
… 165 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga 740 WX - P 901 CH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga 740 WX - P 901 CH in the language / languages: All languages as an attachment in your email.

The manual is 110,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info