Manual Stiga 740 WX - P 901 CH (page 167 of 588) (All languages)

608664

167

Zoom out

Zoom in

1/588

9.10.1 Charging by the engine

This method is only an option if there is still

enough charge in the battery to be able to start the

engine.

• If the battery is new, connect the relative leads.

• Take the machine outside. Alternatively, connect

an exhaust extraction device to the engine’s

exhaust pipe to remove toxic fumes.

• Start the engine by following the instructions

provided in this manual.

• Leave the engine running continuously for 45

minutes (the time needed to fully charge the

battery).

• Stop the engine.

9.10.2 Charging with a battery charger

Use a constant voltage battery charger.

Use of a standard charger may damage

the battery.

For further information, please contact

your dealer.

Before connecting the battery charger,

disconnect the battery from the electri-

cal system.

9.10.3 Disassembly/assembly

The battery is housed under the bonnet.

During removal/installation of the battery, connect

and disconnect the leads as follows:

1. During removal. First disconnect the black

lead from the battery’s negative terminal (-).

Then disconnect the red lead from the batte-

ry’s positive terminal (+).

2. During installation: First connect the red

cable to the battery’s positive terminal (+).

Then connect the black cable to the battery’s

negative terminal (-).

If the leads are disconnected/con-

nected in the wrong order, there is a

risk of a short-circuit and damage to the

battery.

Inverting the cable connections will da-

mage the alternator and the battery.

Tighten the cables securely. Loose ca-



The engine must never be driven with

the battery disconnected. There is a

risk of serious damage to the alternator

and the electrical system.

9.10.4 Cleaning

If the battery terminals are coated with oxide, they

should be cleaned.

Clean the battery terminals with a wire brush and

lubricate them with terminal grease.

9.11 AIR FILTER, ENGINE

For the frequency of this intervention

see chapter 13.

For this maintenance operation, see

also the manual for the engine supplied

with the machine.

9.11.1 Cleaning / Replacement - mod.:

[B&S Power Built] [B&S Intek] (32)

For the frequency of this intervention

see chapter 13.

 -

placed more often if the machine opera-

tes on very dusty ground.

Remove/install the air lters as follows:

1. Clean carefully around the air lter housing

(32:A).

2. Remove the air lter cover by unscrewing the

two screws.

3. Remove the paper lter (32:B). Make sure

that no dirt gets into the carburettor. Clean

the air lter housing.

4. Clean the paper lter by tapping it gently

against a at surface. If the lter is very dirty,

replace it.

5. Assemble the lter by performing the above

instructions in reverse order.

Compressed air or petroleum-based solvents

such as kerosene must not be used for cleaning

the paper lter insert. This will damage the lter.

The paper lter insert must not be oiled.

9.11.2 Cleaning / Replacement - mod.:

[B&S Vanguard] (33)

For the frequency of this intervention

see chapter 13.

 -

placed more often if the machine opera-

tes on very dusty ground.

Remove/install the air lters as follows:

1. Carefully clean around the air lter cover.

2. Remove the air lter cover (33:A) by remo-

ENGLISH

(Translation of the Original Instructions)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga 740 WX - P 901 CH in the language / languages: All languages as an attachment in your email.

The manual is 110,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga 740 WX - P 901 CH Manual

Product: