608664
160
Zoom out
Zoom in
Previous page
1/588
Next page
6.9 IGNITION /HEADLIGHT BLOCK (11:C;
12:C)
The ignition block is used for starting and stopping
the engine.
It is also used to switch on the headlight.
Do not leave the ignition key in position
2 or 3 when you leave the driving seat.

the engine through the carburettor) and
-
ged.
The four ignition key positions:
1. Stop position – the engine is short-circui-
ted. The key can be removed.
2. Operating position – headlight activated.
3. Operating position – headlight not
activated.
4. Start position – the electric starter motor
is activated when the key is turned to this
position. Once the engine has started,
let go of the key which will return to the driving
position 3. Turn the key to position 2 to light the
headlight.
6.10 POWER TAKE-OFF (11:D; 12:D)
A lever for engaging and disengaging the power
take-o for operating front-mounted accessories.
The PTO must never be engaged when
the front attachment lift is in the tran-
sport position. This will destroy the belt
drive.
Lever forward – PTO disengaged.
Lever back – PTO engaged.
6.11 HOUR METER (13:A)
Indicates the number of service hours completed.
Only works when the engine is running.
6.12 CUTTING HEIGHT ADJUSTMENT (11:E;
12:E)
The machine is equipped with a control for using
the cutting means with electrical cutting height
adjustment.
The switch allows the user to continuously
adjust the cutting height.
The cutting means are connected to the contact
(13:B).
6.13 TRANSMISSION ENGAGE/DISENGAGE
LEVER (14; 15)
A lever for disengaging the variable transmission.
2WD is equipped with a lever, con-
nected to the rear axle. See (14:A).
4WD is equipped with two levers,
connected to the rear axle (15:A) and the front
axle (15:B).
The engagement/release lever must
never be between the outer and inner
positions. This overheats and damages
the transmission.
The levers allow the user to move the machine
manually (pushing or pulling), without the engine
running.
The two positions are:
Transmission engaged (14:A1; 15:A1-B1) -
transmission engaged for normal operation.
Transmission disengaged (14:A2; 15:A2-B2) -
transmission disengaged. The machine can be
moved by hand.
The machine must not be towed over long distan-
ces or at high speeds. The transmission could get
damaged.
Do not activate the machine with the
transmission disengaged (lever in).
Risk of damage and oil leakage in the

6.14 SEAT ADJUSTMENT (16:B)
The seat can be moved backwards and
forwards to suit the driver as indicated
below:
1. Move the control lever (16:A) upwards.
2. Set the seat to the desired position.
3. Release the control lever (16:A) to lock the
seat.
The seat is equipped with a safety switch that is
connected to the machine’s safety system.
This means that when no-one is sitting in the seat
the machine cannot be started. (see 7.6.2).
6.15 BONNET
See 5.2 for how to access the fuel cock,
battery and engine.
EN
ENGLISH
(Translation of the Original Instructions)
14
160


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga 740 WX - P 901 CH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga 740 WX - P 901 CH in the language / languages: All languages as an attachment in your email.

The manual is 110,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info