Manual Stiga 740 WX - P 901 CH (page 158 of 588) (All languages)

608664

158

Zoom out

Zoom in

1/588

5.3.2 Battery charging

The battery must be fully charged befo-



Please refer to 9.10 for the battery char-

ging procedure.

5.4 SEAT

NOTE! To facilitate installation of the

seat, apply a drop of oil to the four

screws before screwing them in.

1. Remove the following components from the

seat bracket:

• 4 Nuts (for blocking during transport, not

used).

• 4 Screws.

• 4 Shoulder washers.

• Position the seat over the mounting in the

seat bracket.

1. Install the shoulder washers on the screws.

2. Insert the screws with the attached shoulder

washers through the slots in the seat bracket

and the holes in the seat plate. Screw the

seat into place.

Tightening torques 9±1.7 Nm

If the screws are tightened more than

9±1.7 Nm, the seat will be damaged.

1. Check that the seat moves easily in the slots

in the bracket.

The seat can be folded. If the machine is parked

outside where it is exposed to rain, tip the seat

forward to protect the seat cushion from getting

wet.

5.5 STEERING WHEEL (8)

In order to minimise axial play in the steering co-

lumn, place the 0.5-mm and/or 1-mm shim/s (3:C;

3:B) on the steering column between the sleeves,

pos. (8:A) as follows:

1. Install the sleeve (8:B) on the steering co-

lumn and secure in place by inserting one

of the pins (8:C) by approximately 1/3 of its

length.

2. Pull the sleeve and steering column upwards.

3. Check that the 0.5-mm shim, the 1.0-mm

shim (or both) can be inserted into the gap

which is created in point (8:A).. The shim/s

must not be forced in, as there must be a

little axial play.

4. Remove the pin (8:C) using a pin punch (8:D)

and remove the sleeve.

5. Install the shim/s as indicated in point 3

above.

6. Install the sleeve on the steering column and

secure by inserting both pins completely.

Block the steering column.

5.6 TOW BAR (9)

Install the tow bar (9:B) on the rear of the machine.

Use the screws and nuts (9:A; 9:C).

Tightening torque: 22 Nm.

5.7 QUICK-RELEASE SUPPORTS (1:N)

The quick-release supports and relative installa-

tion instructions are supplied in a separate box

inside the machine packaging.

Install the quick-release supports on the machi-

ne’s front axles.

5.8 TYRE PRESSURE

For the tyre pressure, please refer to chap. "0

TECHNICAL DATA TABLE".

5.9 ATTACHMENTS

For installation of attachment, see the installation

guide accompanying each attachment.

Note: In this case the cutting means as-

sembly is considered an attachment.

6 CONTROLS

6.1 MECHANICAL ATTACHMENT LIFT PE-

DAL (10:C)

The control lever (10:C1) is used to take the

accessories from the operating position to the

transport position.

• Transport position: press the pedal right down

then lift your foot o: the pedal stays down.

• Working position: press and slowly release the

pedal.

Do not attempt to switch to the tran-

sport position while the hooked-up

attachment is in operation. This will de-

stroy the drive belt.

6.2 PARKING BRAKE PEDAL (10:B)

Never press the pedal while driving.

There is a risk of overheating the power

transmission.

ENGLISH

(Translation of the Original Instructions)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga 740 WX - P 901 CH in the language / languages: All languages as an attachment in your email.

The manual is 110,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga 740 WX - P 901 CH Manual

Product: