758029

Steinel L 710 LED Manual

7
Zoom out
Zoom in
Previous page
1/55
Next page
– 12 – – 13 –
GB
Manual override (Fig.6.2)
1) Activate manual override:
Switch OFF and ON twice. The light is set
to manual override for 4 hours. Then it returns
automatically to sensor mode.
2) Deactivate manual override:
Switch OFF and ON once. Light goes out or
switches to sensor operation.
Important:
Switching must take place within 0.2 to 1 second.
Adjusting the detection zone (Fig.6.3-6.6)
The detection zone can be limited to suit require-
ments. The shrouds supplied with the unit can be
used to mask out as many lens segments as you
wish. This prevents the light from being activated
unintentionally, e.g. by cars, passersby etc., and
allows you to target danger spots. The shrouds can
be cut along the grooved vertical divisions. Then
you simply clip them onto the lens.
7. Maintenance
The product requires no maintenance.
The light can be cleaned with a damp cloth (without
detergents) if dirty.
8. Disposal
Electrical and electronic equipment, accessories
and packaging must be recycled in an environmen-
tally compatible manner.
Do not dispose of electrical and electronic
equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste
Electrical and Electronic Equipment and its imple-
mentation in national law, electrical and electronic
equipment no longer suitable for use must be col-
lected separately and recycled in an environmentally
compatible manner.
9. Manufacturer's Warranty
This STEINEL product has been manufactured
with the utmost care, tested for proper operation
and safety and then subjected to random sample
inspection. Steinel guarantees that it is in perfect
condition and proper working order. The warranty
period is 36months and starts on the date of sale
to the consumer. We will remedy defects caused by
material flaws or manufacturing faults. The warranty
will be met by repair or replacement of defective
parts at our own discretion. The warranty shall not
cover damage to wear parts, damage or defects
caused by improper treatment or maintenance.
Further consequential damage to other objects shall
be excluded. Claims under the warranty will only be
accepted if the unit is sent fully assembled and well-
packed with a brief description of the fault, a receipt
or invoice (date of purchase and dealer’s stamp) to
the appropriate Service Centre.
Service:
Our Customer Service Department will repair faults
not covered by warranty or after the warranty
period. Please send the product well-packed to
your nearest service station.
MANUFACTURER'S
1
3
5
YEAR
GB
WARRANTY
MANUFACTURER'S
YEAR
WARRANTY
MANUFACTURER'S
YEAR
WARRANTY
5. Mounting
• Check all components for damage.
• Do not use the product if it is damaged.
• When installing the LED luminaire, make sure the
installation site is not subject to vibration.
• Select an appropriate mounting location, taking
the reach and motion detection into considera-
tion.
Mounting procedure
• Switch OFF power supply (Fig.4.1)
• Undo screws (Fig.5.1)
• Press catch and pull luminaire o the wall mount
(Fig.5.2)
• Undo retaining strap and terminal and remove
luminaire (Fig.5.3)
• Mark drill holes (Fig.5.4)
• Drill holes and insert wall plugs (Fig.5.5)
• Pierce sealing plug for power supply lead
(Fig. 5.6)
• Concealed mounting (Fig.5.7)
• Surface mounting (Fig.5.8)
• Attach retaining strap and terminal to the wall
mount (Fig.5.9)
• Connect conductors (Fig.5.10)
• Remove retaining strap on lamp side and store in
wall mount (Fig.5.11)
• Install luminaire enclosure on wall mount
(Fig.5.12)
• Tighten screws (Fig.5.13)
• Switch ON power supply (Fig.5.13)
• Make settings ➜ "6.Function"
6. Function
Factory settings
Time setting: 5 seconds
Twilight setting: daytime operation
Night light: OFF
Time setting (Fig.6.1H)
The light's stay ON time can be set to any period
from approx. 5 seconds to a maximum of 15min-
utes. Any movement detected before this time
elapses will restart the timer.
Twilight setting (Fig.6.1G)
The chosen response threshold can be infinitely
varied from approx. 2 to 2000 lux.
– Control dial set to = daylight mode
(depending on ambient brightness)
– Control dial set to = twilight mode
(approx. 2 lux)
Night light (Fig.6.1.F)
Standard programme
– Soft light start / no night light
What is soft light start?
The sensor-switched light features a soft light start
function. This means that when turned ON, the light
is not switched directly to maximum output but con-
stantly builds up brightness to 100% within a short
period of time. Brightness is also gradually reduced
when the light is switched OFF.
User-friendly economy programme
– Soft light start + night light until the middle of the
night
– Night light ON as from selected light-level setting
until the middle of the night
How does the user-friendly economy pro-
gramme work?
The sensor-switched light does not have an
integrated clock. The middle of the night is only
determined on the basis of the length of darkness
phases. To work perfectly, therefore, it is important
for the sensor-switched light to be permanently
connected to the power supply during this period.
During the first night (calibration phase), the night
light remains activated throughout the night. The
values are saved even in the event of a mains power
failure. We do not recommend interrupting the pow-
er supply in this the programme. The values are de-
termined over several nights. The sensor-switched
light should, in the event of any fault occurring, be
monitored over several nights to ascertain whether
the switch-o time moves towards midnight.
User-friendly programme
– Soft light start + night light
– Night light ON as from light-level setting selected
What is night light?
Night light provides illumination at night of ap-
prox. 10% light output. The light only switches to
maximum output (100%) for the time selected in
response to movement in the detection zone. The
light then switches back to night light (approx. 10%).
Nightmatic programme
– Soft light start, no night light, no movement
evaluation
– Switches ON at 100% if the light level falls below
the level set
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel L 710 LED at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel L 710 LED in the language / languages: All languages as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info