758029
6
Zoom out
Zoom in
Previous page
1/55
Next page
– 10 – – 11 –
Abmessungen (B×T×H) 260×140×77 mm
Netzspannung 220-240 V, 50/60 Hz
Leistung
Stand by
• Betrieb
<0,5 W
8,4 W
Lichtleistung (lm) 751 lm
Ezienz (lm/W) 90 lm/W
Nachtlicht 10 %
Lebensdauer LED 50.000 h (L70B10 nach LM80)
Farbtemperatur 3000 K
Farbwiedergabeindex RA>80
Sensortechnik Passiv-Infrarot
Erfassungsbereich 360°
Reichweite max. 8 m tangential
Zeiteinstellung 5 s - 15 min
Dämmerungseinstellung 2-2000 Lux
Schutzart IP 44
Schutzklasse II
Temperaturbereich - 20 bis +40°C
10. Technische Daten
Störung Ursache Abhilfe
Leuchte ohne Spannung Sicherung hat ausgelöst,
nicht eingeschaltet,
Leitung unterbrochen
Kurzschluss in der Netzzuleitung
Eventuell vorhandener Netzschalter
aus
Sicherung einschalten, tauschen,
Netzschalter einschalten, Leitung
überprüfen mit Spannungsprüfer
Anschlüsse überprüfen
Netzschalter einschalten
Leuchte schaltet nicht ein Dämmerungseinstellung falsch
gewählt
Netzschalter AUS
Sicherung hat ausgelöst
neu einstellen
einschalten
Sicherung einschalten, tauschen,
evtl. Anschluss überprüfen
Leuchte schaltet nicht aus dauernde Bewegung im
Erfassungsbereich
Bereich kontrollieren
Leuchte schaltet nicht
komplett aus
Nachtlicht gewählt Programmwahlschalter auf
Leuchte schaltet ohne
erkennbare Bewegung ein
Leuchte nicht bewegungssicher
montiert
Bewegung lag vor, wurde jedoch
vom Beobachter nicht erkannt
(Bewegung hinter Wand, Bewegung
eines kleinen Objektes in unmittel-
barer Leuchtennähe etc.)
Gehäuse fest montieren
Bereich kontrollieren
11. Betriebsstörungen
GB
1. About this document
Please read carefully and keep in a safe place.
Under copyright. Reproduction either in whole or
in part only with our consent.
Subject to change in the interest of technical
progress.
Symbols
!
Hazard warning!
...
Reference to other information in the
document.
2. General safety precautions
!
Disconnect the power supply before
attempting any work on the unit.
During installation, the electric power cable being
connected must not be live. Therefore, switch o
the power first and use a voltage tester to make
sure the wiring is o-circuit.
Installing these units involves work on the mains
voltage supply; installation must therefore be
carried out professionally in accordance with the
applicable national wiring regulations and electri-
cal operating conditions (e.g.: DE-VDE0100,
AT-ÖVE/ÖNORME8001-1, CH-SEV1000)
Only use genuine replacement parts.
Repairs may only be made by specialist work-
shops.
3. L710LED
Proper use
LED light with sensor for indoor and outdoor wall
mounting.
The integrated infrared sensor detects the invisible
heat radiated from moving objects (people, animals,
etc.). The heat detected in this way is converted
electronically into a signal that switches the light
ON automatically. Heat is not detected through
obstacles, such as walls or panes of glass, and will
therefore not activate the light.
Important:
The most reliable way of detecting motion is to
install the sensor-switched light with the sensor
aimed across the direction in which a person would
walk and by ensuring that no obstacles (such as
trees and walls, for example) obstruct the line of
sensor vision. Reach is limited when walking directly
towards the light.
Package contents (Fig.3.1)
Luminaire
Wall mount
Two screws
Two wall plugs
Three spacers
Shrouds
Product dimensions (Fig. 3.2)
Product components (Fig. 3.3)
A Sealing plug
B Wall mount
C Connecting terminal
D Luminaire enclosure
E Retaining strap
F Night light
G Twilight setting
H Time setting
I Sensor unit
Detection zone (Fig.3.4-3.6)
4. Electrical connection
Wiring diagram (Fig.4.1)
The supply lead is a three-core cable:
L = phase conductor (usually black,
brown or grey)
N = neutral conductor (usually blue)
PE = protective-earth conductor (green/yellow)
If you are in any doubt, identify the conductors
using a voltage tester; then disconnect from the
power supply again. Connect phase (L) and neutral
conductor (N) to the connecting terminal; optionally,
protective-earth conductor (PE) can be connected
to terminal (E).
Important:
incorrectly wired connections will produce a short
circuit later on in the product or fuse box. In this
case, you must identify the individual conductors
once again and reconnect them. A mains switch for
switching the product ON and OFF may, of course,
be installed in the mains supply lead. The light
source of this luminaire cannot be replaced. If the
light source needs to be replaced (e.g. at the end
of its service life), the complete luminaire must be
replaced.
GB
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel L 710 LED at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel L 710 LED in the language / languages: All languages as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info