720686
8
Zoom out
Zoom in
Previous page
1/14
Next page
8
Electrical Connection
Be sure your power supply agrees with the nameplate
marking. A voltage decrease of 10 percent or more will
cause a loss of power and overheating. All B&D tools are
factory tested. If this tool does not operate, check the power
supply.
Familiarization
Place the saw on a smooth, flat surface such as a
workbench or strong table. Examine Figures 1 & 2 and refer
to the parts description to become familiar with the saw and
its various parts. The following section on adjustments will
refer to these terms and you must know what and where the
parts are. The part name is followed by the corresponding
part number Example - lock down pin (10). Press down
lightly on the operating handle and pull out the lock down
pin (10), as shown in Figure 3. Gently release the downward
pressure and allow the arm to rise to its full height. Use the
lock down pin when carrying the saw from one place to
another. Use the operating handle (1) to transport the saw
or the hand indentations (11) shown in Figure 2 after
unplugging.
Specifications
Capacity of cut
47° mitre left and right
47° bevel left
0° mitre -Max. Height 3-1/2” -Max. Width 5-1/2”
45° mitre -Max. Height 3-1/2” -Max. Width 4-1/8”
45° bevel -Max. Height 2-1/2” -Max. Width 5-1/2”
Bench Mounting
Bench mounting holes (8) are provided in all four feet to
facilitate bench mounting, as shown in Figure 1. (Two
different sized holes are provided to accommodate different
sizes of screws. Use either hole, it is not necessary to use
both.) Always mount your saw firmly to prevent movement.
To enhance the tool’s portability, it can be mounted to a
piece of 1/2" or thicker plywood which can then be clamped
to your work support or moved to other job sites and
reclamped.
NOTE: If you elect to mount your saw to a piece of plywood,
make sure that the mounting screws don’t protrude from the
bottom of the wood. The plywood must sit flush on the work
support. When clamping the saw to any work surface, clamp
only on the clamping bosses where the mounting screw
holes are located. Clamping at any other point will interfere
with the proper operation of the saw.
CAUTION: To prevent binding and inaccuracy, be
sure the mounting surface is not warped or
otherwise uneven. If the saw rocks on the surface,
place a thin piece of material under one saw foot until the
saw sits firmly on the mounting surface.
Installing a New Saw Blade
(UNPLUG THE MITRE SAW)
DO NOT USE FERROUS METAL or masonry cutting blades
in this saw
Loosen hex bolt on center cover counter clockwise with
box wrench.
Lift up the safe cover and center cover.
Press down the lock to lock spindle.
Loosen hex bolt clockwise with box wrench, then
dismount the bolt and flange.
Mount the blade of saw on spindle. Make sure that the
arrow direction on surface of saw blade is same as one
of the cover.
Note: There are two different internal diameters of cutter in
inner plate which have steel stamp marked 25.4mm 16mm.
When mounting, the outer diameter of inner plate must be
correspondent with the internal diameter of saw blade.
Mount flange and hex bolt.
Press axle lock and tighten hex bolt counter clock wise
with box wrench firmly, then tighten hex bolt clockwise to
fix centre cover.
Note: Only use attached wrench when mounting or
dismounting saw blade. When dismounting saw blade, lift up
safe cover and centre cover. Loosen hex bolt with box
wrench and disassemble hex bolt, flange and saw blade.
NEVER DEPRESS THE SPINDLE LOCK PIN WHILE THE
BLADE IS ROTATING.
Be sure to hold the guard bracket down and firmly
tighten the guard bracket screw when you finish installing
the saw blade. Failure to do so will cause serious
damage to the saw.
Assembling and Adjusting Your Saw
PERFORM ALL ASSEMBLY WITH SAW UNPLUGGED.
Attach Mitre Clamp Handle
Remove the mitre clamp handle (4) from the plastic parts
bag and carefully thread it into the bracket in the front of the
saw.
Attaching Dust Bag
A zippered cloth dust bag is included with your saw. To
attach the bag, fit the plastic opening firmly over the dust
spout (9).
NOTE: The saw can also be used with a vacuum cleaner
hose attached to the dust spout or without any attachment.
Adjustments
PERFORM ALL ADJUSTMENTS WITH THE MITRE SAW
UNPLUGGED
ENGLISH (Original instructions)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STSM1510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STSM1510 in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info