622190

Stanley STHT1-12185 -APC-2IN1 Manual

7
Zoom out
Zoom in
Previous page
1/130
Next page
advantage because it will not accidentally drive a fastener
if the tool is contacted against the work - or anything else -
while the operator is holding the trigger pulled.
Before handling or operating this tool:
Read and understand the warnings contained in this manual.
Refer to the Tool Technical Data to identify the operating
system on your tool.
TOOL OPERATION CHECK
CAUTION: Remove all fasteners from tool before performing
tool operation check.
TRIGGER OPERATED TOOL:
A) With the finger off the trigger, hold the tool with a firm grip
on the handle.
B) Place the nose of the tool against the work surface.
C) Pull the trigger to drive a fastener. Release the trigger and
the cycle is complete.
Caution: The tool will cycle each time the trigger is pulled!
SEQUENTIAL TRIP OPERATION
A) Without touching the trigger, press the safety trip against
the work surface.
THE TOOL MUST NOT CYCLE.
B) Hold the tool off the work surface and, avoiding to point
the tool at self or others, pull the trigger.
THE TOOL MUST NOT CYCLE.
C) With the tool off the work surface, pull the trigger. Press
the safety trip against the work surface
THE TOOL MUST NOT CYCLE.
D) Without touching the trigger, press the safety trip against
the work surface then pull the trigger.
THE TOOL MUST CYCLE.
m TOOL USE
Having checked that the tool is working properly, press the
nose against the work piece and pull the trigger. Check
whether the fastener has been driven as required.
l If the fastener is not driven deep enough, increase the
air pressure by 5-6 psig. (0.5 Bar) at a time, checking the
result after each adjustment. Do not exceed the maximum
permissible working pressure (see Tool Technical Data)
l If the fastener is driven too deeply, reduce the air pressure
by 5-6 psig (0.5 Bar) at a time, checking the result after
each adjustment. Do not try to use less than the minimum
working pressure (see Tool Technical Data).
Always try to work with the lowest possible air pressure. This
will reduce the noise and vibration produced and will extend
the life of the internal components such as the bumper.
LOADING THE TOOL:
STHT1-12184 (APC-BN) & STHT1-12185 (APC-2IN1)
l Depress magazine release button and pull back magazine.
(Fig 1)
l With magazine fully open, insert fasteners. Points must be
against bottom of magazine. (Fig 2a & 2b)
l Push magazine forward. (Fig 3)
l Continue pushing until latch is engaged. (Fig 4)
STHT1-12183 (APC-FN)
l
Open the magazine: pull pusher back to engage latch. (Fig 1)
l With magazine fully open, insert fasteners from rear. Points
must be against bottom of magazine. (Fig 2).
l Close magazine: release latch by pulling latch tab and
pusher together slightly to disengage. Slide pusher against
the nails. (Fig 2 & 3)
FASTENER CONTROL ADJUSTMENT- STHT1-12184 (APC-BN) /
STHT1-12185 (APC-2IN1) / STHT1-12183 (APC-FN) (FIG 5)
Fastener control adjustment feature provides close control
of the fastener drive depth; from flush with the work surface
to shallow or deep counter sink. First, set the air pressure
for consistent drive in the specific work, then use the control
adjustment to give the desired depth of drive.
JAM RELEASE- STHT1-12185 (APC-2IN1) /
STHT1-12183 (APC-FN) (FIG 6).
Warning: Always disconnect the air before clearing a jammed
fastener.
1. Depress the latch button
2. With the latch button depressed, rotate the latch assembly
upwards and forwards until latch is on upward position.
3. Clear jam
ADJUSTING THE MULTI-DIRECTIONAL EXHAUST
STHT1-12185 (APC-2IN1) / STHT1-12183
(APC-FN) / STHT1-12184 (APC-BN) (FIG 7)
To adjust the multi-directional exhaust simply rotate the
exhaust deflector to the desired position as illustrated by the
arrows.
FT72124-a-0611_Tool_Manual_AW.indd 7 05/07/2011 17:01
… 7 …


Need help? Post your question in this forum.

Forumrules
1

Forum

stanley-stht1-12185--apc-2in1

Reset search

  • I have just bought a brad nailer model STHT1-12184 (APC-BC). According to Screwfix catalogue this gun accepts their 16ga Brad nails.(Screwfix ref 91803). I thought you could only use a max 18gauge with this tool or am I wrong? Submitted on 1-4-2019 at 15:38

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT1-12185 -APC-2IN1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT1-12185 -APC-2IN1 in the language / languages: All languages as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info