Manual Stanley DN55-8-5 (page 7 of 12) (English)

720675

Zoom out

Zoom in

1/12

2. FEATURES (Pics. 1-2-3)

A. Pressure Switch: The pressure switch is the

activation mechanism that is used to start and stop

the compressor. When the switch is “On”, the motor

and pump will compress air until tank pressure

reaches the upper limit of the factory set operating

pressure. When tank pressure falls below the factory

set “cut in” pressure, the compressor will again

automatically start to compress air.

B. Tank Pressure Gauge: The tank pressure gauge

indicates the air pressure that is present in the tank

in PSI (and BAR).

C. Regulated Pressure Gauge: The regulated

pressure gauge indicates the amount of pressure

that is allowed into the discharge line according to

the setting of the regulator.

D. Regulator Knob: The regulator knob is used

to adjust the air pressure that is available at

the discharge line. The discharge air pressure

is increased by turning the knob clockwise and

decreased by turning the knob counter clockwise.

E. Drain Valve: Ball style valve that drains moisture

from the tank when opened.

F. Quick Coupler: The quick coupler is used to connect

the airline to your tool.

G. Safety valve: The safety valve is set to avoid over-

pressurization of the air tanks. This valve is factory

pre-set at 8 bar (116 PSI) and will not function unless

tank pressure reaches this pressure. Do not attempt

to adjust or eliminate this safety device.

Any adjustments to this valve could cause

serious injury. If this device requires service or

maintenance, see an Authorized Service Center.

3. SCOPE OF USE

The compressor is designed for generating compressed

air for tools operated by compressed air.

Please note that our equipment has not been designed

for use in commercial, trade or industrial applications.

Our warranty will be voided if the machine is used in

commercial, trade or industrial businesses or for equivalent

purposes.

The machine is to be used only for its prescribed purpose.

Any other use is deemed to be a case of misuse. The user/

operator and not the manufacturer will be liable for any

damage or injuries of any kind caused as a result of this.

4. ELECTRICAL GROUNDING

INSTRUCTIONS

This product should be electrically grounded. In the event

of an electrical short circuit, grounding reduces the risk of

electrical shock by providing an escape wire for electrical

current. This product is equipped with a cord having

a grounding wire with an appropriate grounding plug.

The plug must be plugged into an outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

4.1 Connection of the mains plug

Important!

The wires in the mains lead fitted to this product are

coloured in accordance with the code shown in pic. 4.

● Thisproductisdoubleinsulatedandthereforedoes

not require a connection to earth.

● The3pinplugmustcomplytoBS1363/A.

● FusemustcomplytoBS1362.

If for any reason the 13 amp plug fitted to this product

requires replacement it must be wired in accordance with

the following instruction:

Do not connect the brown (live) or blue (neutral) to the

earth pin marked ‘E’ onthe3pinplug.

Connect the Blue wire to the terminal marked Neutral (N).

Connect the Brown wire to the terminal marked Live (L).

Ensure that the outer insulation is gripped by the cord grip

and that the wires are not trapped when replacing the plug

cover. The mains lead on this product is fitted with a 13

amp (BS1363/A) plug. A 13 amp (BS1362) fuse must be

fitted in the plug.

If in doubt consult a qualified electrician

There are no user serviceable parts inside this product

except those referred to in the manual. Always refer

servicing to qualified service personnel. Never remove

any part of the casing unless qualified to do so; this unit

contains dangerous voltages.

Warning!

For your protection if this product is to be used outdoors it

should not be exposed to rain or used in damp locations. Do

not place the product on damp surfaces, use a workbench

if available. For added protection use a suitable residual

current device (R.C.D.) at the socket outlet.

Note: If the mains cable requires replacing it must be

replaced with an identical one and fitted by a

qualified person.

5. PRE-START PROCEDURES

● Examine the machine for signs of transit damage.

Report any damage immediately to the company which

delivered the compressor.

● Verifythatthetankshavebeendrainedandareclearof

any moisture or dirt.

● The compressor should be set up near the working

consumer.

● Avoidlongairlinesandlongsupplylines(extensions).

● Makesuretheintakeairisdryanddust-free.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stanley DN55-8-5 in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stanley DN55-8-5 Manual

Product: