Manual SpinMaster Pottery Cool Studio (page 7 of 8) (English, French)

683468

Zoom out

Zoom in

1/8

1. Form half of a disk of clay into a ball with your hands and

place in center of the turntable.

2. Turn the machine to “|” (slow), spray with water (5-10 sprays)

and press on each side until ball looks smooth and round.

Spray water as needed.

3. Press your finger into the top until a shallow indent forms.

4. Turn the machine “0” (off) and remove from turntable using

the knife tool.

5. Add turtle details using excess clay and tools.

6. Completely dry overnight before painting.

NOTE: Always store extra clay in a resealable plastic bag to

prevent clay from drying out.

1. Prendre un demi-disque d'argile, le rouler entre les mains

pour en faire une boule et le placer au centre du plateau

rotatif.

2. Placer l'interrupteur sur | (lent), vaporiser d'eau (5-10

pulvérisations) et appuyer de chaque côté jusqu'à obtenir une

boule lisse et arrondie. Vaporiser d'eau autant que

nécessaire.

3. Appuyer sur la partie supérieure avec les doigts pour former

un creux.

4. Placer l'interrupteur sur «0» (OFF) et détacher la poterie du

plateau rotatif à l'aide de l'outil à évider.

5. Créer les détails de la tortue à l'aide de l'excédent d'argile et

des outils.

6. Laisser sécher complètement jusqu'au lendemain avant de

peindre.

Remarque: Toujours conserver l'excédent d'argile dans un sac en

plastique hermétique afin d'éviter qu'elle ne se dessèche.

TURTLE DISH

POT TORTUE

TIPS

CONSEILS

1. Cleaning Tips: after each project is completed, wash and dry all

components before storing or starting a new project. If clay has

dried on any tools, soak in a container for 10 minutes to soften. Do

not immerse the machine into water.

2. Patching holes or cracks: if clay disk cracks or creates holes when

forming around the sleeve, add a small piece of clay to that area

and smooth with fingers.

3. To remoisten clay: spray 3-4 times with water, then place in a

resealable bag overnight.

4. Adding details to your project: you can add extra clay details to your

project (like ears, eyes, body parts etc.) securely by using the knife

tool to draw small lines into both surfaces. Then stick.

5. Stamping and Etching: add decorative details to the clay by pressing

the sculpting or knife tools’ motif (diamond/arow/star/heart) into the

clay. You can also press the tool holder’s patterns into the clay. This

works best on a flat surface, or place your fingers behind the clay

for support.

6. Drying your project: to speed up drying,

rotate or flip project every few hours.

Clay will darken.

7. Using paints: to open, pinch with your

fingers. Stir the paint colors thoroughly

before use. Add one or two drops of

water if too thick.

1. Conseils de nettoyage : une fois un projet terminé, laver et sécher tous

les composants avant de les ranger ou de démarrer un nouveau projet. Si

de l'argile a séché sur les outils, les faire tremper dans un récipient

pendant 10minutes afin qu'elle ramollisse. Ne pas plonger la machine

dans de l'eau.

2. Combler les trous et les fissures : si le disque d'argile se fissure ou que

des trous sont visibles autour de la gaine, y ajouter un petit morceau

d'argile et lisser avec les doigts.

3. Pour réhumidifier l'argile : vaporiser 3-4 fois avec de l'eau, puis

placez-la dans un sac refermable jusqu'au lendemain.

4. Orner le projet: Il est possible d'ajouter des éléments en argile au projet

(notamment des oreilles, des yeux, des parties du corps, etc.) en toute

sécurité. Il suffit d'utiliser l'outil à évider pour façonner de petites lignes

sur les deux surfaces. Ensuite, colmater.

5. Estampage et dessin: ajouter des détails décoratifs à l'argile en enfonçant

le cœur, l'étoile, la flèche ou le diamant présent sur l'outil de sculpture ou

l'outil à évider dans l'argile. Il est également possible d'enfoncer les

motifs du porte-outil dans l'argile. Travailler sur une surface plane ou

placer ses doigts derrière l'argile en guise d'appui.

6. Sécher le projet: pour accélérer le séchage, faire pivoter le projet à

intervalle de quelques heures. L'argile devrait alors noircir.

7. Utiliser les peintures: pour ouvrir les pots, pincer avec les doigts. Bien

mélanger les peintures avant de les utiliser. Ajouter une ou deux gouttes

d'eau si le mélange est trop épais.

1 2

3 4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of SpinMaster Pottery Cool Studio in the language / languages: English, French as an attachment in your email.

The manual is 1,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

SpinMaster Pottery Cool Studio Manual

Product: