683468

SpinMaster Pottery Cool Studio Manual

3
Zoom out
Zoom in
Previous page
1/8
Next page
1. Insert the round core and round sleeve into the turntable.
2. Center clay disk on sleeve and press the sides to form the
clay around the sleeve. Avoid pressing too hard on top edge.
If holes or cracks form, don’t worry - you can patch with a
piece of clay.
3. Turn the machine to “|” (slow) and spray the clay with water.
(10-12 sprays)
4. Cup your hands around the clay and apply strong pressure
on each side until the clay becomes smooth and even.
5. Keep working the clay down to the base until clay covers the
entire sleeve, including the rim. If needed, spray lightly with
more water. When your are satisfied with your design, turn
the machine to “0” (off).
6. Create a finished edge using the knife tool to trim excess
clay around rim. (Store extra clay in a resealable plastic bag
to prevent clay from drying out.)
7. To remove your project, remove turntable from machine and
press down onto work surface. Your project should lift off
from the turntable. Slide the flat side of the knife under the
sleeve if it is not lifting.
8. To avoid cracking, remove the round core and wait 15-20
min before removing the soft sleeve.
9. Then remove the round sleeve and use the small coring tool
to create holes in rim. Use a twisting motion.
10. Completely dry overnight before painting. (To speed up the
drying time, flip your project over after a few hours.)
1. Insérer le moule rond et la gaine ronde dans le plateau rotatif.
2. Centrer le disque d'argile sur la gaine et appuyez sur les
côtés pour façonner l'argile tout autour. Éviter d'appuyer trop
fort sur le bord supérieur. Si des trous ou des fissures se
forment, pas d'inquiétude: il est possible de les combler avec
un bout d'argile.
3. Placer l'interrupteur sur | (lent) et vaporiser l'argile avec de
l'eau (10-12pulvérisations).
4. Mettre les mains autour de l'argile et appuyer fermement sur
chaque côté jusqu'à ce que l'argile soit lisse et uniforme.
5. Continuer à travailler l'argile jusqu'à la base, de manière à
recouvrir toute la gaine, y compris le bord. Si nécessaire,
pulvériser à nouveau un peu d'eau. Lorsque le résultat est
satisfaisant, placer l'interrupteur sur «0» (OFF).
6. Pour une finition propre, enlever l'excédent d'argile autour du
bord à l'aide de l'outil à évider (conserver l'excédent d'argile
dans un sac en plastique hermétique afin d'éviter qu'elle ne
se dessèche.)
7. Pour détacher la poterie, retirer le plateau rotatif de la
machine et l'appuyer sur le plan de travail. La poterie devrait
se détacher du plateau rotatif. Faire glisser le côté plat de
l'outil à évider sous la gaine si elle ne lève pas.
8. Afin d'éviter les fissures, retirer le moule rond et attendre
15-20minutes avant de retirer la gaine souple.
9. Ensuite, retirer la gaine ronde et utiliser le petit outil à évider
pour créer des trous dans le bord. Effectuer un mouvement
de torsion.
10. Laisser sécher complètement jusqu'au lendemain avant de
peindre. (Pour accélérer le temps de séchage, faire pivoter le
projet au bout de quelques heures.)
JEWELLERY HOLDER
PORTE-BIJOUX
1 2
3 4
5 6
7
8
9
3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for SpinMaster Pottery Cool Studio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of SpinMaster Pottery Cool Studio in the language / languages: English, French as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info