Manual Spartherm Nova E H2O (page 20 of 28) (English)

810449

Zoom out

Zoom in

1/28

GB 20

5.1 CLEANING THE HEAT EXCHANGER

The heat exchanger can only function at full efficiency if it is regularly

and properly cleaned and serviced. Cleaning must always be executed in a

cooled-down state! As the heat exchanger directly cools down the flue gases

of the Nova E H2O fireplace insert, and this unavoidably results in deposits

on the surfaces of the heat exchanger, these surfaces must be cleaned with

the provided brush on a regular basis. The frequency of cleaning depends

on several factors (use intensity, duration of burning, fuel, chimney draught,

etc.) and a general statement concerning frequency cannot be made.

Initially, we recommend cleaning approximately every 4 weeks. If heavy

contamination does not occur, the interval can be extended. The cleaning

intervals must be adapted to the local conditions. With the use of dry fire-

wood, a functional return flow temperature boost and compliance with our

recommendations, the cleaning intervals can be significantly extended.After

the heating season ends, thorough cleaning of all components is necessary.

The heat exchanger is always cleaned through the combustion chamber

of the fireplace insert. For this, the fireplace door must be opened and the

flame deflector plates (flame baffle plate) must be taken out of the combus-

tion chamber. Next, the thermally activated flue gas damper is removed

through the combustion chamber (see Fig. 6a). For this, the damper is tilted

slightly by the handle and taken out in a downwards direction. Clean the

thermal flue gas damper with a hand brush. Then the turbulators (bent

pieces of sheet metal in the flue gas pipes) are pulled downwards and out

into the combustion chamber with pliers. Subsequently, the heat exchanger

pipes and the middle channel, as well as the outer surfaces of the heat

exchanger, must be cleaned with the provided brush or a hand brush. Then

the deposits fall automatically into the combustion chamber and they can

be removed with standard aids (ash shovel, ash broom or an ash vacuum).

After cleaning, assembly is executed in the reverse sequence.

First, hook in the thermal flue gas damper (introduce diagonally from below

and place on the supports). Then slide in the turbulators (these do not

require a specific direction) and insert the flame baffle plates in such a

manner that the flue gas gap is on the rear of the device.

ASupport

BAutomatic flue gas damper with handle

C8 turbulators in the heat exchanger pipes

DHandle - flue gas damper

ENo turbulators in the rear heat exchanger

pipes

Fig. 6a

Fig. 6b

5.2 CLEANING THE DOUBLE GLAZING

The operator must only clean the double glazing on the combustion chamber

side and the setup room side in accordance with the instructions in the

operating manual. If the inner panes in the hollow space are contaminated,

then cleaning must only be executed by the customer service organisation

or a trained specialised company. In operation, a slight bright shimmer may

be seen between the glass panes. However these deposits do not constitute

grounds for complaint.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Spartherm Nova E H2O in the language / languages: English as an attachment in your email.

The manual is 3.39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spartherm Nova E H2O

Spartherm Nova E H2O User Manual - German - 28 pages

Spartherm Nova E H2O User Manual - Dutch - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Spartherm Nova E H2O Manual

Product: