810449
18
Zoom out
Zoom in
Previous page
1/28
Next page
GB 18
The slot that occurs between the steel
body and the baffle plate is a measure
for reducing the smoke that escapes
from cold tiled stove inserts in the case
of flue gas systems with excessively low
delivery pressure in the start phase.If the
insert is in operation for approx. 15-20
minutes, the necessary delivery pressure
is built up via the after-burning zone
or the flue gas system and the heating
gases are almost exclusively discharged
to the rear.
Through the arrangement of the deflector plate and baffle plate, an
after-burning zone is produced where extremely high heating gas
temperatures occur. Fine dust particles and carbon are burned in this zone.
The combustion chamber lining is removed in the reverse sequence. Impor-
tant: When removing and installing, you must ensure that the chamotte does
not hit against edges, fall over, etc. The service life of the elements of the
combustion chamber lining is reduced through mechanical damage.
If replacement chamotte bricks are required, they can be requested through
the stove fitter with the appropriate order numbers.
3. INITIAL COMMISSIONING
Heat generation systems must only be produced and installed by specialised
companies. The initial commissioning must only be executed by an expert
employee of the installation company. A certificate confirming proper
installation and proper adjustment / function of all control components and
safety components must be given to the owner / operator of the system.
The initial commissioning must only be executed after all necessary
components are connected and all necessary safety devices are integrated
and functional. Before the stove / fireplace insert is placed in service, it
must be filled and ventilated on the heating side (heating network) and water
side (thermal discharge safety device; safety heat exchanger). After the fill-
ing process, check all hydraulic connections for leaks. Operation without
a water-side connection results in irreparable damage and invalidates any
warranty claims!
The first four firings must each be executed with max. 2.0 kg/hour of dry
and thin wood (max. circumference 25 cm). Through this measure the
fireplace insert, the chamotte and the vermiculite are slowly tempered and
thus the moisture that may be present due to storage, transport, etc. is
slowly dissipated. If this does not occur, contamination of the area between
the glass panes, as well as tearing of the chamotte are possible.
Moreover, the operator must be instructed in detail concerning the operation,
function and maintenance of the overall system, including all supplemental
components. In addition, the measures for maintaining safe operation of
the system must be communicated to the operator. Execution of instruction
must be documented in the commissioning protocol! The installation and
operating manual must always be kept in good condition in the vicinity of
the Nova E H2O, where it can be easily accessed.
4. OPERATION
For operation, also comply with the instructions in the operating manual
of the fireplace inserts. The instructions in this installation and operating
manual refer to special operation of a heating insert with integrated water
heat exchanger, such as the Nova E H2O.
Fig. 5d
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spartherm Nova E H2O at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spartherm Nova E H2O in the language / languages: English as an attachment in your email.

The manual is 3.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spartherm Nova E H2O

Spartherm Nova E H2O User Manual - German - 28 pages

Spartherm Nova E H2O User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info