812372
21
Zoom out
Zoom in
Previous page
1/24
Next page
level. 100% is the maximum possible power of the controller.
Min. Speed
The minimum speed of the pump is determined here. During the setting, the pump runs in the respective speed and the flow can be determ-
ined.
The specified percentages are variables, which may deviate more or less strongly depending on the system, pump and pump
level. 100% is the maximum possible power of the controller.
Setpoint
This value is the control setpoint for mode 3 " Variant " on page 20, only version 2.3, and 4.. If this value is below at the sensor, the speed is
reduced. When it is exceeded, the speed is increased.
Time & Date
Serve to set the current time and date.
For time-dependent functions such as circulation and anti-legionella and the evaluation of system data, it is essential that the
time is accurately set on the controller. Please note that the clock continues to run for about 24 hours if the mains voltage is
interrupted, and afterward must be reset. Improper operation or an incorrect time may result in data being cleared, recorded
incorrectly or overwritten. The manufacturer accepts no liability for the recorded data!
Sensor Calibration
Deviations in the temperature values displayed, for example. due to cables which are too long or sensors which are not positioned optim-
ally can be compensated for manually here. The settings can be made for each individual sensor in steps of 0.5 °C.
Settings are only necessary in special cases at the time of initial commissioning by the specialist. Incorrect measurement val-
ues can lead to unpredictable errors.
Commissioning
Starting commissioning help guides you in the correct order through the basic settings necessary for commissioning, and provides brief
descriptions of each parameter in the display. Pressing the ‚esc‘ key takes you back to the previous value so you can look at the selected
setting again or adjust it if desired. Pressing ‚esc‘ more than once takes you back to the selection mode, thus cancelling the commissioning
help (" Commissioning help " on page 14).
May only be started by a specialist during commissioning! Observe the explanations for the individual parameters in these
instructions, and check whether further settings are necessary for your application.
Factory settings
All settings can be reset, returning the controller to its delivery state.
All of the controller‘s parametrization, statistics, etc. will be lost irrevocably. The controller must then be commissioned once
again.
Heat quantity
Constant flow
If “Constant flow” is activated as the type of heat quantity metering, the approximate heat from the manually entered values for antifreeze,
its concentration and the flow from the system and the measured sensor values from the collector and storage are calculated. Additional
information about antifreeze, its concentration and the flow of the system is required. Additionally through the setting offset ∆T, a correction
factor can be set for the heat quantity collection. Since the collector temperature and the storage temperature can be used for the heat
quantity metering, depending on the system, there may be deviations from the displayed collected temperature to the actual previous tem-
perature or the displayed storage temperature to the actual return temperature. Through the setting Offset ∆T, this deviation can be cor-
rected.
21
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel STDC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel STDC in the language / languages: English as an attachment in your email.

The manual is 2.95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel STDC

Sorel STDC User Manual - German - 26 pages

Sorel STDC User Manual - Dutch - 48 pages

Sorel STDC User Manual - French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info