812372
20
Zoom out
Zoom in
Previous page
1/24
Next page
Signal type
Only available, if the function is used on one of the V-outputs. The type of device to be controlled is set here.
0-10V: Controlled by a 0-10V signal.
PWM: Control by means of a PWM signal.
Output Signal
In this menu the type of actors are set: heating pumps have the greatest output with a small input signal, solar pumps in contrast have very
little output with a small input signal. Solar = normal, heating = inverted. For 0-10 V pump always choose the "Normal" setting
PWM / 0-10V off
This voltage / this signal is emitted if the actor is turned off (actor with cable break detection require a minimum voltage / a minimum signal).
PWM / 0-10V on
This voltage / signal is required the actuator to switch on and run at minimum speed.
PWM / 0-10V max.
With this value, the maximum voltage level / maximum signal can be specified for the highest speed of the actuator, which is used, for
example, during the purging or manual operation.
Show signal
Represents the set signal in a graphic and text overview.
Speed control
If the speed control is activated, it STDC offers the possibility through a special internal electronic system to change the speed of pumps
depending on the process. The relay R1, R2 and the Pwm and 0-10V outputs can work with the speed controlled.
This function should only be activated by a technician. Depending on the pump being used and the pump level, the minimum
speed may not be set too small, because the pump or the system may be damaged. The specifications from the affected man-
ufacturer must be observed for this! When in doubt, the min. speed and the pump level should be set too high instead of too low.
Variant
The following speed variants are available here:
Off: There is no speed regulation. The connected pump is only turned on or off with full speed.
Mode M1: The controller changes to the set max. speed after the purging time. If the temperature difference ∆T between the reference
sensors is below the set switch on temperature difference ∆T R1, the speed will be reduced. If the temperature difference between the ref-
erence sensors is above the set switch on temperature difference ∆T R1, the speed will be increased. If the controller has decreased the
speed of the pump to the smallest level and the ∆T between the reference sensors is still only ∆Toff, the pump will be turned off.
Mode M2: The controller changes to the set min. speed after the Speed. If the temperature difference ∆T between the reference sensors is
above the set switch on temperature difference ∆T R1, the speed will be increased. If the temperature difference ∆T between the reference
sensors is below the set switch on temperature difference ∆T R1, the speed will be reduced. If the controller has decreased the speed of the
pump to the smallest level and the ∆T between the reference sensors is still only ∆Toff, the pump will be turned off.
Mode M3: The controller changes to the set min. speed after the Speed. If the temperature on the reference sensors is above the set value to
be set in the following, the speed will be increased. If the temperature on the reference sensors is below the set value to be set in the fol-
lowing, the speed will be reduced.
Purging time
For this time, the pump runs with its full speed (100%) in order to guarantee a secure start-up. Only after expiration of this purging time will the
pump have a controlled speed and will switch, depending on the set variant, to the max. or min. speed. Speed.
Sweep time
With the control time, the inertia of the speed control is determined in order to prevent strong temperature deviations as much as possible.
The timespan is entered here, which is needed for a complete cycle from minimum speed to maximum speed.
Max. Speed
The maximum speed of the pump is determined here in %. During the setting, the pump runs in the respective speed and the flow can be
determined.
The specified percentages are variables, which may deviate more or less strongly depending on the system, pump and pump
20
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel STDC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel STDC in the language / languages: English as an attachment in your email.

The manual is 2.95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel STDC

Sorel STDC User Manual - German - 26 pages

Sorel STDC User Manual - Dutch - 48 pages

Sorel STDC User Manual - French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info