812372
23
Zoom out
Zoom in
Previous page
1/24
Next page
10. Language
To select the menu language. During initial commissioning and longer power inter-
ruptions, the query is made automatically. The choice of languages may differ
depending on the model. Language selection is not available for every model.
Malfunctions/Maintenance
Replacing the Fuse
Repairs and maintenance may only be performed by a specialist. Before working on the unit, switch off the power supply and
secure it against being switched on again! Check that there is no power flowing!
Only use the supplied spare fuse or a fuse of the same design with the following specifications: 2 AT/250 V.
If the mains voltage is switched on and the controller still does not function or display anything,
then the internal device fuse may be defective. First find the external fault source (e.g. pump),
replace it and then check the device fuse.
To replace the device fuse, open the device as described under "" wall Installation " on page 11",
remove the old fuse, check it and replace if necessary.
Then first recommission the controller and check the function of the switch outputs in manual mode
as described in Section 3.2..
Maintenance
In the course of the general annual maintenance of your heating system, the functions of the controller should also checked by
a specialist and the settings should be optimized if necessary.
Performing maintenance:
lCheck the date and time " Time & Date " on page 21
lAssess/check plausibility of statistics " Statistics " on page 15
lCheck the error memory " Message Log " on page 15
lVerify/check plausibility of the current measurement values " Measurement values " on page 14
lCheck the switch outputs/consumers in manual mode " Manual " on page 16
lPossible optimization of the parameters setting (only on customers request)
Possible error messages
Possible error messages Notes for the specialist
Sensor x defective Means that either the sensor, sensor entrance on the controller or the connecting wire was defective
(" Temperature Resistance Table for Pt1000 Sensors " on page 13).
Collector alarm Means that the temperature on the collector set under “Collector protection" was exceeded.
Restart Means that the controller was restarted, for example, due to a power outage. Check date & time!
Time & Date This display appears automatically after a longer network disruption, because the time & date must
be examined and, if applicable, adjusted.
23
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sorel STDC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sorel STDC in the language / languages: English as an attachment in your email.

The manual is 2.95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sorel STDC

Sorel STDC User Manual - German - 26 pages

Sorel STDC User Manual - Dutch - 48 pages

Sorel STDC User Manual - French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info