680782
63
Zoom out
Zoom in
Previous page
1/88
Next page
63
S10931-00001_Rev-D_EN
12. twin operation
12.1 twin operation
Two operators can be controlled with one control unit,
for example in a double garage with two garage doors.
Both operators are connected to one control unit for this
purpose.
2
1
Fig. Installation example for twin operation, slave (1) and
master (2)
Mode of operation
If one of the operators receives a command and
starts to move, the other operator is locked for this
time. The other operator can only be started after the
movement has stopped.
INFORMATION
Both operators cannot be operated at the
same time.
12.2 Installing the operators
The installation of the operators is described here using
an example.
1. Install the operators on the two doors as described in
the Chapter "6. Installation."
12.3 Selecting and configuring master
and slave
Requirements
Both operators are configured as a master in the factory
settings. The main communication with the control unit
is effected via the master.
INFORMATION
No automatic closing function and no
energy-saving mode are possible in twin
operation.
1. Set DIP switches 1 and 3 on the wall control unit to
"ON." This sets membrane keypad T1 for the master
and membrane keypad T2 for the slave.
T1
T2
Fig. Membrane keypad T1 and T2 of wall control unit
T1 for master
T2 for slave
GND
+24V
gn
rt
+
-
Fig. Connection of chain and track for both operators to the
control unit
Terminal block Function
gn + Track
rd - Chain
2. Connect the operator (1) to the terminal blocks for
chain (rd) and track (gn) of the wall control unit.
The connection cable must be firmly secured to
prevent displacement.
3. Connect the wall control unit to the mains voltage.
Check that the power supply is connected.
4. Configure the operator (1) as the slave. To do this,
establish a connection to the motor carriage via
SOMlink and a WiFi-enabled device.
5. In the menu, under the "twin operation" settings,
configure "Operator is slave" for the selected
operator and save the entry. Check the entry.
6. Disconnect the wall control unit from the mains
voltage.
7. Connect operator (2), the master, to the wall control
unit in parallel to the terminal block for chain and
track. The connection cable must be firmly secured
to prevent displacement.
8. Reconnect the control unit to the mains voltage.
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9080 pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9080 pro in the language / languages: English as an attachment in your email.

The manual is 10,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9080 pro

Sommer S 9080 pro User Manual - German - 88 pages

Sommer S 9080 pro User Manual - Dutch - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info